搜索资源列表
MyOQAM
- OFDM/OQAM调制解调源码,另外增加了上变频部分,中心频率30KHz-OFDM/OQAM modulation and demodulation ,also include up frequency to 30Khz
max261
- 通过编写的上位机程序向单片机发送品质因子Q,中心频率F0,单片机通过串行通信接收Q,F0,从而实现89C2051单片机的驱动Max261滤波芯片过程序,单片机使用 X25045芯片作为外部看门狗电路-Sent via the PC program to the microcontroller Q, f0, via the serial communication allows the device receiving Q, f0, achieve 89c2051 microcontroller
AFC9854testKey
- MSP430F控制AD9854,并行,LCD显示,矩阵键盘控制,幅频特性测试仪,2013全国电设E题,数字扫频信号源,线性扫频,对数扫频,点频,中心频率,3dB带宽-MSP430F control AD9854, serial, LCD display, matrix keyboard control, amplitude frequency characteristics of the test instrument, the 2013 national electric E title, d
find_UWB
- 超宽带中心频率及带宽计算matlab模拟-uwb central frequency calculation
FRFT
- 利用分数阶傅立叶变换进行信号参数估计,本程序是对LFM信号的参数中心频率和调频斜率进行估计-Use FRFT signal parameter estimation, the parameters of this program is the center frequency and frequency rate LFM signal is estimated
suijixinhaochuli
- 第一个程序为模拟产生一个正态随机序列X(n),画出产生的随机序列波形、相关函数(与理论曲线对比) 和功率谱密度。第二个程序为产生一个信号X(n),绘出信号及其幅度频谱曲线,当中心频率向左搬移f0=200Hz时,求出其低通等效信号,并绘出其幅度频谱、信号的同相、正交分量及包络。当中心频率向左搬移f0=100Hz时,求出其低通等效信号,并绘出其幅度频谱、信号的同相、正交分量及包络。-The first program to simulate the amount of generating a
coupling-coefficients
- 通过设置中心频率、带宽、无载Q值和反射损耗计算切比雪夫G值和耦合系数。-By setting the center frequency, bandwidth, unloaded Q and reflection loss calculation chebyshev G value and the coupling coefficient.
Split-beam-method-estimated-target-
- 分裂波束法估计目标方向 ULA(均匀线列阵),16个阵元,LFM信号的中心频率为25KHz,带宽为1KHz,信号时宽为150ms。求来波方向的估计值 。-Split beam method estimated target direction ULA (uniform linear array), array element 16, the center frequency LFM signal is 25KHz, a bandwidth of 1KHz, the signal width
CIC_filter
- 抽取:(接收端) 中频信号IF 20M(采样率是50M) 下变频信号 MIX_O 1M(50M) 采用CIC滤波器进行降采样率。 插值:(发送端) 基带信号上变频到1M,采样率是2.5M,采用CIC滤波器进行升采样率处理。 注释:升采样率或者降采样率不会改变原始信号的中心频率,但是频谱分布会发生改变。-Extraction: (receiver) IF signal 20M (sampling rate is 50M) down-conversion signal M
CP1.2
- 单馈电右旋圆极化切角式微带天线HFSS仿真设计,中心频率2GHz-Single-feed chamfer right hand circularly polarized microstrip antenna HFSS simulation design, the center frequency of 2GHz
music
- 该算法是利用MUSIC算法求解信号频率问题,可用于载波中心频率求解等等。-The algorithm is a MUSIC algorithm using signal frequency problem.It may be solved for the carrier center frequency and the like.
opt
- CTP协议实现CTP的原理和实现机制,并通过实验测试了WLAN干扰对无线传感器网络传输性能的影响,初步的实验研究验证了CTP协议的自适应机制,同时也显示了WLAN对WSN的影响,当WSN的射频输出功率小于10 dBm时,基于CTP的WSN经常无法成功组网 当WLAN的中心频率与WSN的中心频率重叠时,基于CTP的WSN的信标比例与跳数显著增加。-CTP Protocol implementation
radar
- 1、目标速度引起的失真,时间膨胀因子10%、chirp中心频率偏移5%。 2、超高速运动对脉冲压缩的影响,多普勒频移补偿(Distortion caused by target speed, time dilation factor 10%, and chirp center frequency offset 5%. Effects of ultra high speed motion on pulse compression and Doppler frequency shift comp
microstriparray
- 在设计microstrip patch antenna:输入中心频率、介质基板厚度和介电常数,得到 patch的设计参数和馈电位置(In the design microstrip patch antenna: input center frequency, dielectric substrate thickness and dielectric constant, get patch design parameters and feed position)
LTE_earcfn
- lte_频点计算: 计算上下行中心频率(需已知频点号,即NDL) 下行计算公式:FDL = FDL_low + 0.1(NDL-NOffs-DL) 其中FDL为该载频下行频点,FDL_low对应频段的最低下行频点,NDL为该载频下行频点号,NOffs-DL对应频段的最低下行频点号。 上行计算公式:FUL = FUL_low + 0.1(NUL-NOffs-UL) 其中FUL为该载频上行频点,FUL_low对应频段的最低上行频点,NUL为该载频上行频点号,NOffs-UL对应频段的
HHT
- 完全从理论公式出发。网格化后中心频率很重要,大家从连续数据变为离散的角度去思考,相信应该很容易理解(Starting from the theoretical formula completely.After the grid center frequency is very important, everyone to think, from the perspective of continuous data into discrete believe that should be easy
sir-10
- 基于三通带交叉耦合带通滤波器的设计,中心频率在2.4Ghz和3.4Ghz及5.5Ghz(Design of cross coupling bandpass filter based on three passband)
FFT
- 主要为适用于STM32的FFT变换程序,适用于做滤波模块时的中心频率提取(Center frequency extraction for filtering module)
VMD
- 信号处理的一种方法,将信号按中心频率分为几个频带,适合多频带信号。(Decomposition signal)
6TS
- AWR仿真L波段六阶带通滤波器,有一对关于中心频率对称的传输零点(six-pole transmission zero)