搜索资源列表
keil5
- 读取到ADX345的xyz值后，串口打印输出(After reading the XYZ value of the acceleration sensor ADX345, the serial port prints and outputs)
inputtest
- 本实验利用TIM5_CH1来做输入捕获，我们将捕获PA0上的高电平脉宽，并将脉宽时间通过串口打印出来，大家可以通过按WK_UP按键，模拟输入高电平。同时，本实验将保留上一个实验的PWM输出，DS0还是会由暗-->亮的循环变化，大家可以通过杜邦线连接PA0和PB5，来观测PWM输出的高电平时间。(This experiment uses TIM5_CH1 to do input capture, we will capture the PA0 high level pulse width,
ourdev_725194H96GRW
- STM8ADC采样，单路ADC中断采样。然后串口打印出来显示(STM8ADC sljfiwa sj lsfos sljfie snfi fjsol lhi jfiehg slhojah fjiwo)
88
- 此程序能够烧入STM32实现距离测量 通过串口打印返回距离值(This procedure can be burned into the STM32 to measure the distance through the serial print return distance value)
第30章：复数FFT的实现
- 按下按键K1，串口打印函数的计算结果和采样波形。(1. press button K1, serial port print function arm calculation results and sampling waveform.)
第28章：ST官方汇编FFT库应用
- 串口打印低通滤波器输出数据。 串口打印高通滤波器输出数据。 串口打印带通滤波器输出数据。(Serial port printing low pass filter output data. Serial port printed high pass filter output data. Serial port printing bandpass filter output data.)
Usart
- 本程序可以用于STM32F10系列芯片，实现串口打印(This program can be used for STM32F10 series of chips for serial port printing)
RFID
- 一个RFID rc522程序，采用的是模拟SPI接口，运行在C51平台上，程序利用串口打印卡ID号，还有卡类型，该文件可用作二次开发。(A RFID rc522 program, using the analog SPI interface, run on the C51 platform, the program uses the serial port Print Card ID number, as well as the card type, the file can be used f
滚球程序V1.0
- 电赛时获取小球位置并输出，支持串口打印图像(During the race, the ball position is obtained and output, which supports the serial port to print the image)
NRF24L01
- NRF24L01驱动,可以组建自己的小型PAN，测试程序里实现了NRF24L01的收发测试，通过串口打印出数据(NRF24L01 Driver for 80C51)
I2CTest_UseSoftI2CModule(PB0,PB1)
- 本程序实现了用TI LM3S系列单片机的IO端口接入I2C总线，可以实时监控总线上的变化与传输，并将I2C传输的内容，实时通过串口打印出来，可用于破解各种I2C通信协议，曾经用于解析PIC单片机之间的I2C通信，解决了串口实时打印的问题，采用FIFO，UART接受与发送均采用中断，并解决了FIFO中断深度等等问题。仅供参考。(This program is used to achieve the IO port access I2C bus by using TI LM3S Series MCU
04_USB读取鼠标
- 读取鼠标传感器坐标，并通过串口打印到串口助手。(Read the mouse sensor coordinates, and print to the serial assistant through the serial port.)
RVMDK（uv5）
- 使用红外接收头接收遥控器的按键，通过串口打印键值。(Use the infrared receiver to receive the key of the remote control, and print the key value through the serial port.)
RVMDK（uv5）
- DHT11温湿度传感器读取，通过串口打印温度和湿度值。学会DTH11温湿度读取，理解OneWire用法。(DHT11 temperature and humidity sensor read, through the serial port Print temperature and humidity value. Learn to read DTH11 temperature and humidity, understand the use of OneWire.)
Texas Instruments DS18B20
- CC2530节点通过采集 DS18B20 温度信息，实时发送到协调器。协调器通过 串口打印和液晶显示方式展示当前温度。(The CC2530 node is sent to the coordinator in real time by collecting the DS18B20 temperature information. The coordinator displays the current temperature by serial port printing and liqui
4AD
- 4路AD采集，串口打印，stm32单片机GPIOPA0,1,2,3口，均值滤波，可连接HC05蓝牙模块，发送数据到手机端(4 road AD collection, serial port printing, stm32 single chip GPIOPA0,1,2,3 mouth, mean filtering, can connect HC05 bluetooth module, send data to mobile phone end.)
ALIENTEK MiniSTM32 实验11 TFTLCD显示实验
- 本实验利用MiniSTM32开发板连接TFTLCD模块，实现TFTLCD模块的显示，下载成功后，通过把LCD模块插入TFTLCD模块接口（靠右插），按下复位之后，就可以看到LCD模块不停的显示一些信息并不断切换底色。同时该实验会显示LCD驱动器的ID，并且会在串口打印（按复位一次，打印一次）。(This experiment is connected with the TFTLCD module using the MiniSTM32 development board, TFTLCD disp
探索者 激光测距串口打印且液晶显示数据
- 在主函数中读取数据，提取到主函数中来，不需要按键(Read the data in the main function, extract it into the main function, and do not need the key)
编码器1.1
- 嵌入式编码器底层代码，51单片机驱动，通过串口打印编码器旋转角度(Embedded encoder bottom code, 51 single chip driver)
DS18B20温度传感器实验
- 1、串口打印出序列号和温度 2、在打印的同时，LED闪烁(1. Serial serial number and temperature are printed by serial port 2. At the same time, LED scintillation)