搜索资源列表
zebra-source
- labview控制ZM400打印条码,串口通讯-labview control ZM400 print bar codes, serial communication
myNFC-v1.3
- 嵌入式stm32通过串口1与NFC模块通信,NFC模块读取mifare卡信息,将此信息最终通过串口2打印到PC端屏幕,同时ucos提供多任务功能,LED1和LED2以多任务方式闪烁-Embedded stm32 1 and the NFC module through the serial port communication, NFC module reads mifare card information, this information is the final print to 2 P
stm32f103-key-button---
- (STM32F1O3 芯片 软件使用Keil 包含了STM32 的所有外设库函数,可用于实际项目应用)程序包含操作GPIO口的使用,可用于其它程序的扩展。按下面板的上下左右键,串口会打印出键值,并点亮对应的LED。-(STM32F1O3 chip contains all the software using the Keil STM32 peripherals library functions can be used for the actual project application) u
ADC3andDMAhighspeed(2.4Msps)
- 硬件平台:STM32F429I-DISCORVERY 软件平台:KEIL MDK5.10 在STM32F429I-DISCO board中,由于串口2被L3GD20和液晶数据线占用,所以串口1很方便,而且还留了2个孔外接。 * 说 明 : 实现printf和scanf函数重定向到串口1,即支持printf信息到USART1 * 实现重定向,只需要添加2个函数: * int fputc(int ch, FILE *f) * int fgetc(FI
STM32_USART
- stm32实现USART通信,通过串口调试助手打印数据-USART achieve STM32 communication, through the serial port debugging assistant print data
Ex015-FM(TEA5767PWM8978)
- 随时操作开发板上的3个按钮或摇杆,串口1会打印出键值。需要连上串口线,打开串口工具进行观察。-Operation at any time the board three buttons or joystick, serial 1 will print out the key. You need to connect a serial cable, open the serial port tool for observation.
LabWindowsCV-serial-and-word-printf
- 通过moudbus协议,实现串口数据采集与发送,以及,可通过界面设置参数与将数据打印到excel表。-Through moudbus agreement, serial port data acquisition and sending, and can set parameters through the interface and the data printed to the excel table.
stm32-handwrite-_recognize
- 基于stm32的手写识别程序:开机的时候先初始化手写识别器,然后检测字库,之后进入等待输入状态。此时,我们在手写区写数字/字符,在每次写入结束后,自动进入识别状态,进行识别,然后将识别结果输出在LCD模块上面(同时打印到串口)。通过按KEY0可以进行模式切换(4种模式都可以测试),通过按KEY2,可以进入触摸屏校准(如果发现触摸屏不准,请执行此操作)。DS0用于指示程序运行状态。-Based stm32 handwriting recognition program: boot time to
Com-Debuger
- 串口调试,可以excel将调试数据打印出来,对调试过程提供很大的便利-Serial debugging, can excel will print debugging data, provide great convenience for debugging process
rfid_mini2440
- 该程序是一个应用程序,需要结合内核自带的驱动程序使用,编译环境是Fedora,运行环境是Mini2440,可实现射频卡的识别,并在串口处打印出射频卡的卡号。-The program is an application that requires a combination of kernel driver that comes with the use of the compiler environment is Fedora, the operating environment is Min
USART3
- 基于stm32 串口3 usart3 支持窗口printf打印-Based on the STM32 serial port 3 usart3 support window printf printing
printf_SD_LCD
- 接受串口数据,存到SD卡,并通过触摸屏打印出来。-Get date uart,save date, and printf by LCD
25
- 串口收发存入flash中然后读取出来数据后接CRC校验,通过出口调试助手打印出来-A serial port to send and receive deposited in the flash and then read after the CRC check
USART1
- 利用STM32的串口1来打印出采集到的数据信号,输出到PC上。-STM32 use serial port 1 to print out the collected data signal output to the PC.
DS18B20_USART
- stm32驱动DS18b20温度传感器,并将采集的温度打印到计算机的串口端-Stm32 drive DS18b20 temperature sensor, and will collect the temperature of the print to the computer serial port
can_test
- 源码为can总线环回测试程序,使用stm32f103c8t6单片机。can接口接入单片机PA11和PA12管脚,串口1(PA2,PA3)打印接收到的数据。源码中使用定时器3计时,每5s发送一次数据,在can中断接收据,在while程序中将接收到的数据打印出来。-Source code for can bus loopback test program using stm32f103c8t6 microcontroller. It can interface to access the micro
stm32-ContikiOS
- STM32 移植使用Contiki系统 1) 不仅是ESP8266驱动,整合了wifi模块、OLED显示器、烟雾传感器、关照传感器、温湿度传感器、超声波传感器,红外热释电传感器。 2) 目录结构: Documents - 说明文档 Hardware - 外围连接设备 Libraries - STM32库依赖项 Listing - 编译链接生成文件 Output - 编译输出文件 Project - 工程项目文件 User - 单片机内部及板
sleep_modes
- 德州仪器tm4单片机进入睡眠模式的实验 ,可以通过按键唤醒,并通过串口发送到电脑打印显示-Texas Instruments tm4 MCU enters sleep mode experiments, you can wake up through the key, and sent to the computer through a serial printer display
8.UART
- ARM上开发的串口通信程序,用于打印调试信息,能像电脑Printf那样使用-On ARM serial communication program development, debugging information for printing, can be used like a computer Printf
uart1auart2
- 串口2接收数据,串口1把串口2接收到的数据打印到上位机上。-A serial port 2 receiving data, a serial port to a serial port 1 2 prints the received data to the upper machine.