搜索资源列表
STM32F10x_USART_example
- STM32F10x_USART串口的同步、异步、中断、DMA传输等范例-STM32F10x_USART serial synchronous, asynchronous, interrupt and DMA transfers
STC-VUart
- 51单片机程序,用端口与定时器模拟串口,全异步通信!-51 use port and timer virtual com.
Project
- 串口通信422总线通信功能异步通信,gengjiakuaisuwenidng-422 serial communication bus communication asynchronous communication
Serial-test-help
- 串口测试助手,基本串口调用模式,异步通信,可设置基本参数,线程读取数据。-Serial test assistant source code, the most basic serial port call, asynchronous communication, thread read data, can set the basic parameters
MFC_com
- 使用VC2005实现异步串口通讯,其中波特率及端口号可调。-VC2005 using asynchronous serial communication, in which the port number and baud rate adjustable.
CommInterface
- 串口、TCP/IP通讯基类,做了缓冲异步IO等修改-Serial,TCP/IP BaseClass
OFAGVE
- 自己编写的一个串口类,支持同步和异步,功能比较强大,已经运用在很多程序中-Oneself write a serial port, supports synchronous and asynchronous, more powerful, has been used in many applications
uart_test
- 描述了利用spatran6系列的FPGA,进行串行异步通信的uart串口实现代码(Describes the use of spatran6 series of FPGA, serial asynchronous communication uart serial port to achieve the code)
mdrssynchronous
- 自己编写的一个串口类,支持同步和异步,功能比较强大,已经运用在很多程序中(Oneself write a serial port, supports synchronous and asynchronous, more powerful, has been used in many applications)
示波器生成类附源码实例
- 虚拟仪器比传统仪器功能更强、可扩展性更好、性价比也更高,是未来测量测试行业的发展方向。完成了一种对马达故障波形进行显示分析的虚拟示波器软件设计,为马达故障分析提供了定量的分析工具。软件采用面向对象的软件设计思想来编写,按照功能划分为5个模块:虚拟示波器界面设计、异步串口通信、Modbus协议软件包、波形傅里叶分析、波形存储访问五大模块,使用VC++基于对话框的应用程序框架完成了这5个模块的详细设计和实现;通过测试,该虚拟示波器操作简单、测量准确,能满足使用要求(Compared with tra
用FPGA实现UART
- 用fpga实现异步串行通信。通过串口助手接收与发送(Implementation of serial communication with FPGA)
16F1823 SCI
- 采用微芯pic16f1823单片机,实现SCI异步串口通信功能,可做初学者参考。(The microchip pic16f1823 MCU, SCI asynchronous serial communication function, can be used for beginners reference.)
CH341A转I2C的Labview应用说明
- CH341A的I2C接口Labview应用说明,CH341A 可以做同步串口、异步串口、并口等使用(CH341A I2C interface Labview application instructions, CH341A can do synchronous serial port, asynchronous serial port, parallel port and so on)
Xmodem
- XMODEM协议是一种串口通信中广泛用到的异步文件传输协议。分为标准Xmodem和1k-Xmodem两种,前者以128字节块的形式传输数据,后者字节块为1k即1024字节,并且每个块都使用一个校验和过程来进行错误检测。在校验过程中如果接收方关于一个块的校验和与它在发送方的校验和相同时,接收方就向发送方发送一个确认字节(ACK)。由于Xmodem需要对每个块都进行认可,这将导致性能有所下降,特别是延时比较长的场合,这种协议显得效率更低。(XMODEM protocol is a widely us
测试程序
- ADUCM360 UART串口学习: UART串口通讯的使用非常广泛,是一个全双工通用异步收发器,兼容工业标准16450,支持DMA。能在串行和并行数据之间可靠的转换。程序的调试常常通过串口发送和接收数据,来修改程序。 异步串行通讯协议包括:a: 5到8比特数据 b:1、2或1.5个停止位,c:无、奇、或偶校验。d:波特率。所有的数据字要求一位起始位和至少一位停止位,产生了支持7至12位范围的字长。(ADUCM360 UART serial learning: UART serial
236226
- 自己编写的一个串口类,支持同步和异步,功能比较强大,已经运用在很多程序中()
723890
- 这是一个封装得比较完整的串口类接口,支持同步,异步操作,使用简单高效()
新建文本文档
- Verilog编写的按键代码,采用异步串口传输协议,并带有偶校验。(Verilog's key code, asynchronous serial port transmission protocol, and with even check.)
615977
- 这是一个封装得比较完整的串口类接口,支持同步,异步操作,使用简单高效()
FPAG UART Verilog
- FPGA实现URAT,实现异步串口收发控制(FPGA implements URAT to realize asynchronous serial port and transceiver control)