搜索资源列表
H2_3
- 这是光电编码器的汇编程序,希望对学习的人有帮助-This is a compilation of optical encoder procedures, and they hope to learn helpful
statemachine
- 基于状态图的光电编码器4倍频vhdl程序,输入相位差90度的两相,输出倍频和方向信号-Based on the state of the optical encoder Figure 4 multiplier vhdl procedure, enter a 90-degree phase difference of two-phase, frequency and direction of the output signal
HB96FHB96N
- 转速测量电路,可测量霍尔传感器、编码器、光电传感器的信号输出,具有1路继电器输出-Speed measuring circuit, measurable, Hall sensors, encoders, photoelectric sensor signal output, with a road relay output
WINCE_optical_encoder
- 讲述在WINCE系统下,如何实现光电编码器的驱动程序,很有参考价值。-WINCE about the system, how to achieve optical encoder driver, a good reference.
gdbmq
- 编码器解码程序正在完善中,但可以参照 光电编码器-Decoder, the program is perfect, but can refer to
BiSS
- BiSS接口的光电编码器数据读出编程BiSS Encoder interface data read-out program-BiSS Encoder interface data read-out program
JUDU
- 《角度测量器》 用光电编码器测量角度,每个脉冲为 0.72 度。 测量范围:0.0~360.0 度 为保证不错过脉冲,用 timer1计数,在电平跳变中断里判断转动方向,尽量加快处理过程。 数据换算和数码管扫描显示在主循环中实现。 -" Angle measuring device" with the optical encoder measuring the angle of each pulse is 0.72 degrees. Measuring
Optical_encode
- 光电编码器对电机转速的测量源程序,传感器为PARALLAX,实测可用。另外包括对左右进步电机的控制程序-Optical encoder on the motor speed measurement source, the sensor is PARALLAX, measured available. Also includes about progress on the motor control program
CPLD_RP
- 基于CPLD,计数功能,可将光电编码器的光电信号计数送至并行端口-Based on CPLD, counting function, optical encoder can be counted optical signal sent to the parallel port
maichongleijiaqicesu
- 用脉冲累加器计光电编码器输出的脉冲个数,用数码管显示速度,数码管用的是A口和E口控制-By using A pulse accumulators program output pulse number of photoelectric encoder, with A digital pipe display speed, digital works is A mouth and E mouth control
noah
- 基于MCS51系列单片机的用于光电编码器传感的绝对角度量的接口与数码管显示程序-programmes for transformation devices from light to electricity with led display functions
PMSM_ABZ
- 基于增量式光电编码器的永磁同步电机转子位置初始定位方法介绍。-Introduction of initial positioning method based on the incremental optical encoder, permanent magnet synchronous motor rotor position.
photoelectric_encoder
- 基于MSP430单片机的光电编码器驱动程序。-MSP430 microcontroller-based photoelectric encoder driver.
STM32F103
- STM32F103使用定时器读取增量式光电编码器-The STM32F103 use timer read incremental photoelectric encoder
guangdianbianmajishu
- 分析解释光电编码器的原理,给出光电编码器输出脉冲的计数方法-Analysis to explain the principle of the photoelectric encoder, given the photoelectric encoder output pulse count
speed
- 速度检测,智能小车车速检测,用的是光电编码器检测,上位机显示数据-Speed detection, smart car speed detection, photoelectric encoder is detected, the host computer display data
matlab20121304
- 一种基于光电编码器和matlab曲线拟合的测速设计-Based on photoelectric encoder matlab curve fitting velocimetry
TWRK40_PMSM_FOC
- 基于Kinetis K40的带光电编码器的永磁同步电机控制程序-3-phase PMSM Vector Control using Quadrature Encoder on Kinetis K40
guangdianbianma
- 光电编码器采集脉冲的程序,采用计数查询等待中断方式, 液晶显示正反转 ,显示脉冲数(60个/转),显示转圈数-Program of photoelectric encoder acquisition pulse counting queries wait for interrupt LCD reversible display the number of pulses (60/rev) to display the number of turns
encoder
- 使用VHDL编写的光电编码器。并且在quartus软件进行仿真。最终下载在FPGA板上实现光电编码器的使用。-Optical encoder using VHDL written. And quartus software simulation. The final use of photoelectric encoder download FPGA board.