搜索资源列表
PWMtim2中断4通道SPWM
- 基于STM32单片机的用于升压或降压电路的pwm控制(PWM control for boost or depressurization circuits)
IGBTboost
- 升压稳定输出,实现MPPT,光伏最大功率追踪(Boost stable output, realize MPPT, photovoltaic maximum power tracking)
bq25703a
- 这是具有系统功率监控器和处理器热量监控器的bq25703A I2C 多化合物电池降压/升压充电控制器(bq25703A I2C Multi-Chemistry Battery Buck-Boost Charge Controller With System Power Monitor and Processor Hot Monitor datasheet)
tidud04
- 此 2kW 隔离式双向直流/直流转换器参考设计 (TIDA-00951) 可在 400V 直流总线和 12 - 14 节锂电池组之间进行电力传输,可用于 UPS、电池备份和电力存储等应用。在备用模式下,此参考设计可用作采用 ZVS 技术的有源钳位升压转换器,将电源从 48V 电池传输至 400V 直流总线。当用作电压馈入式全桥电池充电器,从 400V 直流总线为 48V 电池充电时,此参考设计可实现大于 93% 的效率。此参考设计还设有内置直流总线和电池过流保护,并设有过压保护。(for a 2
2_order_LowPass_filter
- 并网型光伏逆变器环路仿真,两级系统控制。升压和逆变。(PV inverter model simulate)
BOOST-PFC-300v-60hz-100Ω仿真
- 基于psim软件,BOOST升压电路,利用电流和电压双反馈控制纹波和输出波形(BOOST boost circuit.We use current and voltage feedback to control ripple and output waveform.)
boost_close_loop
- 直直变换器,升压型BOOST,闭环可控。simulink仿真模型(BOOST dcdc simulink model close loop)
QT5
- 为了实现电润湿器件的驱动和控制,该系统设计包含驱动电路和上位机软件两部分。驱动电路使用PIC单片机通过FT245组成的USB接口模块接收上位机的控制命令,按照预定义的格式解析生成控制信号控制DA芯片AD5535输出电压信号,使用集成化的电压芯片实现电平转换和升压电路;上位机软件基于Qt软件开发框架在Windows平台下采用C++语言编写,实现对驱动参数的各种操作和电润湿器件电极的状态显示满足经实验验证,该系统工作性能良好(In order to achieve the drive and con
Boost
- Boost 升压电路,一种常见的开关直流升压电路,它可以使输出电压比输入电压高。(Boost step up circui)
BOOST0914
- 利用SG3525完成的升压电路,用altium designer绘制的原理图(Using SG3525 to complete the boost circuit, draw the schematic diagram with Altium designer)
直流升压斩波变换电路
- 该资料为boost变换器的Multisim仿真文件,经过验证可以正常使用(This information is the design data of half bridge transformer, and the selection and design method of half bridge transformer are introduced in detail.)
sigal_boost_PI
- 闭环升压电路MATLAB仿真,波形质量好(MATLAB simulation of closed loop boost circuit)
Classifiers
- 我们需要成百上千的分类器来解决现实世界的分类吗 我们评估179分类17种分类器(判别分析,贝叶斯,神经网络,支持向量机,决策树,基于规则的分类器,升压、装袋、堆放、随机森林和其他合奏,广义线性模型,线性,偏最小二乘法和主成分回归,logistic回归、多项式回归、多元自适应回归样条等方法),实现在WEKA,R(有或没有插入包),C和Matlab,包括所有目前可用的相关分类。(Do-we-Need-Hundreds-of-Classifiers-to-Solve-Real-World-Class
PVandbatery
- 这是一个光伏发电装置与蓄电池构成的新能源发电系统。光伏发电采用典型二级升压结构,并采用最大功率点追踪(MPPT)以获取最大功率(This is a new energy generation system consisting of photovoltaic devices and batteries. Photovoltaic power generation uses a typical two-stage boost structure and uses maximum power poi
BOOST
- 应用matlab/simulink软件搭建,matlab2010版本可用。boost升压电路(Build using matlab/simulink software, matlab2010 version is available. Boost circuit)
MPPT
- 对Boost升压电路进行设计与性能优化; (2)完成DC变换器环节实现光伏最大功率跟踪硬件电路设计,分析其实现最大功率跟踪控制的理论依; (3)研究实现基于DSP光伏最大功率跟踪的算法,及其控制流程图; (4)选择适合的最大功率跟踪算法,编写软件程序实现光伏电池的最大功率输出,尽可能提高光伏发电系统的效率。(In this paper, I will mainly research the maximum power tracking technology of the PV, design a
battery_buckboost
- 基于simulink的双向DCDC仿真,实现高压转低压给蓄电池充电,蓄电池放电可反向升压回馈电网。(Based on simulink's bidirectional DCDC simulation, the battery can be charged at high voltage to low voltage, and the battery discharge can be reverse boosted back to the grid.)
BUCK-BOOST
- DC-DC 中升压 减压 用matlab 仿真buck boost buck-boost各个图形(buck boost buck-boost)
moni
- 直流升压电路输入24输出40, 已经完成电流和电压双闭环控制, 满足大部分扰动的控制(DC boost circuit in 24v out 40v)
buck_boost
- 直流升压降压变换器,可以自由设置参数,运行稳定,可以供研究变换器的使用。(DC step-up and step-down converters can set parameters freely and operate stably, which can be used for research converters.)