搜索资源列表
virtualserialportsdriverxpv5.1.3.41cracksnd
- 通过串口精灵实现虚拟串口来模拟单片机中的串口通信。-spirit through virtual serial port Serial SCM to simulate the serial communication.
164CX
- 这是一个用单片机口模拟串口来驱动74LS164的汇编程序-This is a microcontroller I used to drive simulation Serial compilation procedures AT89C2051
51serialinterfaceapplication
- 51单片机模拟串口,硬件串口,rs232串口例程-51 microcontroller serial simulation, hardware serial port, RS232 serial port routines
MCU_UART
- 使用单片机管脚模拟串口通讯的源程序。使用KEIL C51语言编写,KEIL V7.0环境下编译通过。-use analog microcontroller pin serial communication of the source. Use KEIL C51 language, KEIL billed environment compile.
moni_uart
- 51单片机的模拟串口程序,实现发送功能。 编译环境:keil c51-51 analog microcontroller serial procedures to achieve this function. Build Environment : Keil decoder
chuankoumoli
- 用单片机软件模拟串口程序,只占用一个T2资源,对初学者很有帮助-MCU serial process simulation software, only takes up a T2 resources useful for beginners
SOFT_UART
- 利用STC单片机实现软件模拟全双工串口的程序,只用一个定时器,消耗系统资源很少。-using SCM software simulation of the full-duplex serial procedures, only a timer, depletion of scarce resources system.
monichuankou
- 将单片机IO口模拟为串口发送数据,51单片机可直接编译后使用(若出现错码可适当降低波特率)-The single-chip analog to serial IO port to send data, the microcontroller 51 can be directly compiled using (error code if there may be appropriate to reduce the baud rate)
monichuankoutongxin
- 模拟单片机串口通信;虚拟实验板;基于Configure Virtual Serial Port Driver通信-Configure Virtual Serial Port Driver
ADS1118
- C51编程,ADS1118在C51单片机下利用串口模拟SPI编程-C51 programming, ADS1118 at C51 microcontroller programming using serial port simulation SPI
SPI(STC15F204PNRF24L01)
- STC51单片机GPIO口模拟串口,实现包含UART、SPI、IIC等-STC51 microcontroller GPIO port simulation serial port and realize UART, SPI, IIC, etc
mainSend
- 1、Cmos Sensor OS 测试; 2、主控单片机型号:STC15F4K60S4 3、模拟电子开关:CD4051 CD4067BM96 4、单片机控制模拟电子开关自动采集被测Sensor 各PIN的导通压降,将数据通过串口 发送至上位机,上位机接收数据并对数据进行分析判断,给出最终的OS测试结果; 5、单片机10位精度AD 电压采集; 6、支持单片机串口通信;-1, Cmos Sensor OS test 2, the master SCM model: STC1
UART_IO
- 普通IO口模拟串口,用于单片机串口数量不够的情况下,亲测通过。-Ordinary IO port analog serial port, for the number of SCM is not enough, the pro test.
IOaUART
- 利用单片机IO口模拟UART程序,系统用了一个定时器和一个外部中断,外部中断主要是用来检测串口起始位的到来。-IO mouth simulation UART program, microcontroller system with a timer and an external interrupt, external interrupt is mainly used to detect the arrival of the start bit serial port.
HT66FU50IO-UART
- HT66FU50单片机IO口模拟UART串行口程序,HT66FU50单片机串行口不够用时,可以用此程序模拟串口。-HT66FU50 single-chip IO port analog UART serial port program, HT66FU50 microcontroller serial port is not enough, you can use this program to simulate the serial port.
VB6.0和51单片机实现模拟量输入
- VB6.0和51单片机实现模拟量输入串口通信(VB6.0 and 51 MCU analog input serial communication)
arduino demo
- arduino 开发板数字口 模拟口 I2C口 功能测试 串口数据上传打印端口输入状态 AVR功能测试版(AVR Functional test edition)
简单模拟串行通信
- 使用单片机任意IO口用软件的方法模拟实现异步串行数据传输的方法,并采用多次采样软件方法来增加软件模拟串口通讯的可靠性,在以上基础上,进一步用具有中断功能的IO口来实现数据的接收,从而增加软件模拟方式的实用性和灵活性;
38-比较器做ADC-C语言-模拟串口
- STC15单片机利用ADC做模拟比较器,基于库开发(STC15 MCU uses ADC as a comparator)
基于32单片机的电压检测装置
- 1. 基本功能:基本实现了附件2要求的功能,因为TFT-LCD引脚损坏,故用OLED代替,开发板没有配套24C02,所以使用flash模拟EEPROM,对参数K进行掉电保护。 2. 增加功能: a.按键个数增加1个,多了一个用于时间调整,可以让时间减小。 b.可以通过串口修改实时时间,在屏幕1下,用串口助手输入指令。 c.可以通过串口更新电压上报时间,在屏幕2下,用串口助手输入指令。 d.往串口助手输入:?,即可以获得串口指令提示。更多信息见实验工程下“ReadMe”文件。