搜索资源列表
MSP430_GPS
- MSP430单片机控制GPS模块,通过UART串口接收GPS的经纬度信息和时间日期。-The MSP430 MCU control GPS module via UART serial port to receive GPS latitude and longitude information and the time and date.
51GPS
- 51单片机与GPS模块c语言程序,从GPS模块中截取经纬度信息。-51 and GPS module c language program, the interception of latitude and longitude information from the GPS module.
GPS_Send_Message
- 单片机串口2取GPS时间经纬度等,然后通过GSM发送出去,同时显示发送出去的数据 串口1用于与GSM通信-Microcontroller serial port 2 to take GPS time, latitude and longitude, etc., and then sent via GSM, at the same time display of the data sent out the serial port 1 for GSM communication
final
- PIC18F452单片机0183协议于GPS模块通信。MCCP18编程-PIC18F452 microcontroller 0183 agreement in GPS module communication. MCCP18 programming
UART
- 单片机UART程序,实现和外部器件的数据传输,如GPS,PC机-The microcontroller UART procedures, implementation, and the data transmission of the external device, such as GPS, PC
gprs111
- PIC单片机和GPS现实短信的发射接收功能,其中有各种设置-PIC microcontroller and GPS real SMS transmitting and receiving functions, including a variety of settings
gps_lcd1602
- 基于单片机的GPS数据处理及液晶1602显示的系统设计-System design based on single-chip GPS data processing and liquid crystal display 1602
GPS_msp430_code
- 430单片机,程序的功能是通过串口0以4800,n,8,1的通行格式接收GPS数据,之后将 数据进行解析再通过串口1以4800,n,8,1的通行格式发送到PC机,其中数 据打包发送格式为GPS_DATA_PACKAGE:经度,纬度,速度,航向,水平高度, 海拔高度,卫星,年/月/日,时-分-秒(实际连调时这个数据包由GSM模块直 接发送到后台,在由后台再进行处理得到预期的效果)-The functions of the program through the serial por
dpj
- 基于C语言编写的单片机开发程序、驱动程序 是GPS 无线传输模块 MP3模块-Microcontroller development based on the C language, drivers, GPS wireless transmission module MP3 module
dpj1
- 基于C语言编写的单片机开发程序、驱动程序 温度 mp3 闹钟 gps等模块 -Based on the C language microcontroller development process, the driver temperature mp3 alarm clock gps module
Smart-car-steward
- 本设计以HOLTEK单片机作为汽车的检测和控制的核心,以实现自动控制防盗和安全检测。通过热释红外传感器和磁传感器实现车辆的防盗检测,如车辆被盗,可通过GPS对汽车的轨迹进行定位,并将定位坐标传至通过GSM网络传送至车主手机,让用户实时掌握被盗车辆的位置信息。在车辆行驶过程中,通过震动传感器对行车安全进行检测,如车辆发生以外,可向车主亲人发送车辆的位置信息,让失事车辆及时获救。另外,当车主与车的距离在大约10m以上,汽车会自动上锁;如果距离在大约10m以内,汽车会自动解锁。-The design
12864gps
- 51单片机收集gps信息,12864显示-51 MCU collect gps information
grs-clock-design
- grs时钟设计:授时电路利用gpsoem接收板与atmega128单片机相连实现gps时钟的提取,以及在lcd上进行显示。-grs clock design: timing circuit uses gpsoem receiver board with atmega128 microcontroller connected to achieve gps clock extraction, as well as in the lcd display.
chapter13
- 单片机实现gps定位的源程序,可以实现定位数据传输-MCU gps positioning of the source, can achieve positioning data transmission
proc
- 基于单片机实现GPS定位设计的C程序设计-GPS positioning MCU Design
GPS_STC
- gps数据读取及分析,适用于51单片机,可在12864上显示数据-gps data acquisition and analysis, for 51, the data can be displayed on the 12864
80c51PGPSPLCD
- 80C51 单片机解析GPS数据,并且用LCD显示-80C51 single-chip GPS data analysis, and with the LCD display
GPS51TEST
- 在51单片机上读取GPS数据,在LCD上显示-51 MCU reads GPS data, displayed on the LCD
recive
- 单片机串口接收中断接收数据分析函数,用于串口通信协议,GPS等-Microcontroller serial receive interrupt receiving data analysis functions for serial communication protocols, GPS, etc.
1
- ***用51单片机解析GPS数据并在12864液晶显示经纬度、时钟以及高度的源代码程序-*** Parse GPS data with 51 and 12864 LCD latitude and longitude, and height of the clock source code program