搜索资源列表
DMF-simulink
- 扭振减振器双质量飞轮在加载和卸载工况下的减振特性的仿真曲线-Simulation curve torsional vibration damper dual mass flywheel in the loading and unloading conditions damping characteristics
CYC_CSHVR
- 标准工况参数，本文档是标准工况的速度与时间的关系参数。-Standard working parameters, the parameters of this document is the relationship between the speed of the standard conditions and time.
anysy_study-case
- 【高级建模算例1】椭圆形带孔平面的自适应分析【高级建模算例2】 带孔方板应力集中的子模型分析 【高级建模算例3】多工况载荷下的静力拓扑优化-Example 1 [count] Advanced Modeling Adaptive oval perforated plane analysis [2] Advanced Modeling examples perforated side panels sub-model analysis of stress concentration [3] adv
UniTire_one_in
- 在Matlab/Simulink中对郭孔辉院士的UniTire模型进行了建模，包括纵滑与侧偏的联合工况-In Matlab/Simulink in for Hui Guo academician UniTire model modeling, including joint working conditions of vertical slip and yaw
UniTire_CePian_ZongHua
- 在Matlab/Simulink中对UniTire统一轮胎模型建模，仿真分析纵滑与侧偏的联合工况-In Matlab/Simulink modeling in unified tire UniTire, simulation analysis of longitudinal slip and yaw joint working conditions
ADRC_ini7s_blend_FO_v5_snow_and_ice
- 利用自抗扰控制车辆在冰雪混合路面上的启动工况仿真-ADRC use on snow and ice mixed road conditions to start the vehicle simulation
ADRC_ini7s_blend_FO_v4
- 基于分数阶自抗扰控制的车辆1/4模型在混合路面启动工况仿真-Fractional-based vehicle ADRC 1/4 model start in the mixed road conditions simulation
wind_dirct_drive_
- 风力发电直驱变流器的仿真，某大厂出品，逼近真实工况，互相学习！- Direct drive wind power inverter simulation, some manufacturers produced, close to the real conditions, learn from each other!
SG-level-control
- 蒸汽发生器的水位控制微分方程的求解程序，附带多种工况-use matlab to simulate SG level control under various Working conditions
PV
- 光伏电池板模型，仿真p-u曲线等。自动将excel中的多条不同的温度、光照等数据读入，并连续运行输出保存每个工况数据-PV simulink model。it can read different input initial parameters from excel，then run the pv model and save the power data of each case automatically。
Design_GasTurbine01
- 燃气轮机设计计算：设计稳态工况下压气机、燃烧室、透平各截面热力参数的计算。 -Gas Turbine Performance Calculation, ideal gas working fluid, compressor performance calculations, Turbine performance calculations, ennergy balance for the combustion chamber.
h2d-rotor
- 航空发动机-压气机二维数值模拟程序，包括网格生成，湍流模型，数值迭代算法等，可以计算多个工况-gas turbine simiulation
code_for
- 针对机械行业变转速零件如轴承，齿轮箱的故障诊断，采用阶次分析技术。程序针对变转速工况下的故障诊断。-Variable speed machinery industry parts such as bearings, gearboxes for fault diagnosis using order analysis techniques. Procedures for troubleshooting variable speed conditions.
pso1
- 基于粒子群算法的电力系统负荷分配问题（1）数学模型： 以IEEE 3机6节点为工况模型 ，Load=850MW （2）目标函数： minF=∑(i=1，Ng)Fi(PGi)，Fi(PGi) =aiPi2+biPi+ci+Ei，考虑阀点(Valve-Point)效应 （3）约束条件： a.发电机组输出功率上下限约束，即PGi min<=PGi<= PGimax； b.电力负荷平衡约束，忽略网损，即∑(i=1，Ng)（PGi）= PGD-Based on part
TC-final
- 模拟计算管道停输后工况变化的程序，包括热力和水力计算，得到管中流体温度和压力以及环境参数变化-A code to simulate the pressure and temperature in a pipe after a time of shut down of a oil pipeline, as well as the changing of environment.
phase-equivalence
- C 语言，模拟流体相平衡过程，得到混合气体平衡态以后的工况参数-C language to simulate fluid phase equilibrium process, to obtain a mixed gas equilibrium after working parameters
multiphase-gas-flow
- 用C语言编写的，模拟流体相平衡过程，得到混合气体平衡态以后的工况参数-Clanguage to simulate fluid phase equilibrium process, to obtain a mixed gas equilibrium after working parameters
RSOpt
- 用于优化在各种工况组合下的杆系结构各杆件的截面积，使得结构材料成本最优化-optimization for the section of rods under different load condition
top3
- 由99行经典拓扑优化程序修改，对多工况下的悬臂梁进行刚度优化,得到最优拓扑图。-By 99 lines of classical topology optimization program modification, the cantilever beams stiffness optimization of operating conditions.
coordinated-model
- 将机炉协调控制系统被控对象的非线性数学模型直接用于姚孟发电厂2号机300MW 单元机组的分散协调控制系统(DCS)。通过在线调整模型参数和在相同时间段内对比不同工况下实际受控对象的工程值曲线与仿真模型的计算值，证明了此模型能很好地反映机炉协调被控对象的实际特性，同时也证明了该模型的正确性和准确性-The coordinated boiler-turbine control system nonlinear mathematical model of the controlled object d