搜索资源列表
C8051F060-AD-UART1
- C8051F060 自带高速AD进行数据采集 可达100兆采样率 并切缓存与片外ram 并把采集数据通过串口发送给PC - Data Acquisition example for C8051F060 Descr iption: This example illustrates the use of ADC1 and the DMA to acquire and store data. It is intended for use with the C8051F060
STC1.SPI.ad1256
- 基于STC公司单片机的SPI协议,应用与AD1256的程序。最终将采集到的数据通过串口发送到上位机。-STC microcontroller based company SPI protocol, application procedures and AD1256. Eventually the collected data is sent to the host computer via the serial port.
cs5529testcode
- stc单片机与cs5529 adc转换芯片的一个简单的数据采集系统.单片机通过spi接口发出转换命令,cs5529把模拟量转换成码值送给单片机,单片机把数据通过串口助手显示数据-adc test code
4.7
- XS128的CCD采集赛道的程序,并将采集回来的数据通过串口发送到到上位机进行赛道显示-XS128 CCD acquisition circuit of the program, and to collect data through the serial port to send back to the PC display on track
chuankou
- 串口采集数据,可以采集串口数据,波特率可调。-Serial data acquisition, serial data can be collected, baud rate adjustable.
TCD1206-P-TLC1549
- TCD1206 实现光源的采集,通过1549转换后传给单片机,单片机将数据通过串口传出- TCD1206 realize the collection source, through the 1549 conversion pass microcontroller, the microcontroller outgoing data through the serial port
module
- 串口通讯和AD7842采样程序,用于采集AD数据通过串口传输到上位机-parallel to serial
2-zigbee_cc2530
- 终端节点每隔一段时间采集一次片内温度值,并将结果发送给协调器,同时亮一下led1;路由节点每隔一段时间采集一次电池电压值,并将结果发送给协调器,同时也亮一下led1;协调器每收到一个无线数据,就亮一下led2,同时将数据通过串口发送给电脑。是“LED”,则也亮一下led1。-............................................. no
mainSend
- 1、Cmos Sensor OS 测试; 2、主控单片机型号:STC15F4K60S4 3、模拟电子开关:CD4051 CD4067BM96 4、单片机控制模拟电子开关自动采集被测Sensor 各PIN的导通压降,将数据通过串口 发送至上位机,上位机接收数据并对数据进行分析判断,给出最终的OS测试结果; 5、单片机10位精度AD 电压采集; 6、支持单片机串口通信;-1, Cmos Sensor OS test 2, the master SCM model: STC1
scope_new
- 本实验,为 ZX-2 开发板的综合实验,该实验利用 ZX-2 开发板上的 ADC、独 立按键、 UART 等外设, 搭建了一个具备丰富功能的数据采集卡, ZX-2 开发板负 责进行数据的采集并将数据通过串口发送到 PC 机上, PC 端,利用强大的串口调 试工具——串口猎人,来实现数据的接收分析,并将数据分别以波形、码表、柱 状图的形式动态显示出来,以让使用者能够直观的看到 ADC 采集到的信号细节。 同时,用户也可以使用串口猎人通过串口给下位机( FPGA) 发送指令,下位
TCD1304_drive
- FPGA驱动TCD1304AP线阵CCD,并经采集将数据通过串口传输至上位机-FPGA drives TCD1304AP linear CCD, and by collecting the data transmitted through the first bit machine serial
ZigBee--stack-driving-sht20
- ZigBee终端节点驱动sht20温湿度传感器采集数据,并将数据利用ZigBee协议栈发送到ZigBee协调器,协调器节点将接收到的数据通过串口显示到pc机。-ZigBee terminal node drive sht20 temperature and humidity sensors to collect data, and the data is sent to the use of ZigBee protocol stack ZigBee coordinator, the coordi
2tongdao
- STM32双路同时采集数据,ADC采集数据,串口输出-STM32 dual simultaneous acquisition of data, ADC data collection, serial output
PC-and-mcu-communikation
- 采用Atmel公司的AT89S52为核心,实现PC机与单片机系统之间的数据通信。单片机系统采集温度,将数据通过串口将数据传送至PC机,PC机上实现温度显示。用MAX232芯片完成单片机TTL电平到RS-232双向电平的转换 ;用46的矩阵式键盘完成所要显示的数据发送;用LED七段数码管显示接收和发送的数据。在软件设计方面,PC机采用VB或者VC语言编程,使用通信控件来实现串行口收发数据;单片机方面用中断方式完成数据的接收和发送。-Adopts AT89S52 as the core of Atm
CSerialPort
- VC++串口类文件,建立和打开串口,采集串口数据,包含头文件和源文件-VC++ serial class files, build and open the serial port, serial data collection, including the header and source files
SerialWaveform
- 串口示波器:采集串口输入数据产生波形 波形发生器:根据波形产生串口输出数据-Serial oscilloscope and waveform generator
I2C温湿度采集
- 传感器DHT11,通过I2C采集温湿度数据,然后通过串口打印出来
SHT2x_STM32F103
- 基于 stm32f103c6 采集DHT 传感器数据,并串口输出。(Collecting DHT sensor data)
riceIoT
- 使用数据采集器 将空气质量传感器发送的数据通过串口发送到工控机,实现vb编写监测界面。(The data sent by the air quality sensor is sent to the industrial computer through the serial data collector, and the monitoring interface is written by vb.)
串口输出LSM303DLH
- 使用STM32单片机进行开发,采集LSM303DHL磁传感器数据,希望给大家带来帮助(Use STM32 MCU development, acquisition LSM303DHL magnetic sensor data, hope to bring you help)