搜索资源列表
CEPIN
- 源代码,测量频率,用于51单片机测量频率所用,开发代码-failed to translate
设计一个数字频率计
- 以单片机为核心,设计一个数字频率计,进行频率的自动测量,并用12864液晶屏的第一行显示“数字频率计”,第二行显示设计都姓名和学号,第三行显示测量的频率值(单位:HZ)。 基本部分:数码管显示被测信号的频率,测频范围为1HZ~500KHZ。 发挥部分:扩大测频范围为1HZ~1MHZ。 (2)要求:完成该系统的硬件和软件的设计,在Proteus软件上仿真通过后,提交一篇课程设计说明书。
Digital-frequency-meter
- 用VHDL语言完成数字频率计的设计及仿真。频率测量范围:1~10KHz,分成两个频段,即1~999Hz,1KHz~10KHz,用三位数码管显示测量频率,且用LED(发光二极管)来表示所显示单位,我们这里定义亮绿灯表示以Hz为单位,亮红灯表示以KHz为单位。具有自动校验和测量两种功能。具有超量程报警功能。-Digital frequency meter
2
- 利用msp430单片机中TA模块编写测量频率的程序,经过调试已经可以准确测量频率-failed to translate
MSP44-Frequency-measurement
- 该程序利用MSP430单片机内部定时器的捕获功能,实现对输入方波信号频率的测量,测量频率范围广,并且测量精确。-Frequency measurement by using MSP430 single chip microcomputer internal timer capture capabilities of the program, implementation of input square-wave signal frequency measurement, the measurem
pinlvji
- (FPGA Verilog)测量频率、周期、脉冲宽度 -(FPGA Verilog) measuring the frequency, period, pulse width
cepinfacepinlv
- 基于单片机的频率计的设计。能精测测量频率,并用数码管显示-Based on single-chip frequency meter design. Precision measurement can measure frequencies and with digital display
cepinlv
- 本资料提供的一种基于AVR单片机测频率的方法,可以使得测量频率精确到误差为1HZ-This information provides an AVR microcontroller based frequency measurement method that can make accurate to measure the frequency error is 1HZ
Stm32_template_CAPTURE
- 利用STM32F103引脚捕获测量频率 利用STM32F103引脚捕获测量周期-Using STM32F103 to measure frequency
FPGA-frequency
- 本设计基于FPGA设计等精度频率计,并采用NIOS II控制液晶显示器显示测量频率。-The design is based on FPGA design precision frequency meter, and using NIOS II controlled LCD display shows the measured frequency.
F_H_measure
- msp430 lunchpad 实现定时器触发测量频率-msp430 lunchpad achieve timer to trigger a measurement frequency
数字频率计
- 数字频率计是一种基本的测量仪器,它被广泛应用于航天、电子、测控等领域。采用等精度频率测量方法具有测量精度保持恒定,不随所测信号的变化而变化的特点
shuzipinlvji
- 1.用VHDL完成12位十进制数字频率计的设计及仿真。 2.频率测量范围:1Hz~10KHz,分成两个频段,即1~999Hz,1KHz~10KHz,用三位数码管显示测量频率,用LED显示表示单位,如亮绿灯表示Hz,亮红灯表示KHz。 3.具有自动校验和测量两种功能,即能用标准时钟校验、测量精度。 4.具有超量程报警功能,在超出目前量程档的测量范围时,发出灯光和音响信号。 -1 completed 12 with VHDL design and simulation of d
Cont-Freq-Int-Clk
- 该例程展示了如何利用NI公司的数据采集卡测量频率-This example demonstrates how to acquire frequency data from an SCXI-1126 using the DAQ device s internal clock.
Inputcapture
- STM32的TIM3通用定时器 输入捕获法测量频率 精确到1hz-STM32 of TIM3 general-purpose timer input capture accurate method to measure the frequency 1hz
youwucha
- 测量频率,通过测量脉宽计算频率!寄存器a计算有问题,31Hz以上频率很准,往下频率有时不正确-Measuring frequency, calculated by measuring the frequency of the pulse width! Register a calculation in question, 31Hz frequencies above is very accurate, down to the frequency and sometimes incorrect
123
- 1、 等精度数字频率/相位测试仪是电子通信电路测试设计常需要的一种工具。设计的指标包括,测量频率的范围:(0.1Hz-100MHz),测量精度:測频全域不大于百万分之一。具有脉宽测试功能,相位测试功能。系统的组成框图如下所示,TCLK为待测的信号,BCLK为系统的时钟。其主控制结构如图測频原理所示,采用高速的系统时钟BCLK对待测信号时钟TCLK进行计数,然后计算出一个周期的平均值,最后输出高8位数据。-1, and other precision digital frequency/phase
frequency-measure
- 用430单片机测量频率,等精度法。用两个定时器,实现高精度测量。-MCU with 430 measurement frequency, and other precision method. With two timers, high precision measurements.
FreqTest
- 基于周期法测量频率的单片机程序,已调试通过,很好用,直接加入工程文件即可运行使用。-frequency measure based on MCU。
digital-frequency-meter
- 1.用VHDL完成12位十进制数字频率计的设计及仿真。 2.频率测量范围:1Hz∼ 10KHz,分成两个频段,即1∼ 999Hz,1KHz∼ 10KHz,用三位数码管显示测量频率,用LED显示表示单位,如亮绿灯表示Hz,亮红灯表示KHz。 3.具有自动校验和测量两种功能,即能用标准时钟校验、测量精度。 4.具有超量程报警功能,在超出目前量程档的测量范围时,发出灯光和音响信号。 -1. VHDL design and simulation comple