搜索资源列表
MAIN
- 一种QPSK调制解调算法的误码率仿真-a simulation of demodulation with Qpsk.
uwbbpsk
- 用matlab编辑的关于超宽带通信的BPSK调制的误码率分析,系统仿真时加入高斯白噪声,仿真结果给出了时域和频域图-BER analysis of the ultra wide bank BPSK communication channel with AWGN, time and spectrum figures are given in the end.
bpsk_ask
- 分析了ASK和BPSK通信系统,接收机采用相关器接收分析系统测试和理论误码率-Analyzed ASK and the BPSK communications system, the receiver uses the correlation instrument receive analysis system test and the theory error rate
cdmabpskMul
- 描述DSCDMA多用户系统在AWGN信道下的误码率-Describes the DSCDMA multiuser system under error rate of the AWGN channel
bpsk1
- 利用matlab对BPSK系统的误码率进行仿真，解压无需密码-use matlab to realize the BER of BPSK and it needn t password for extract the file
simu
- DS-UWB的仿真框图，误码率仿真，脉冲发生器，ook和bpsk调制，以及rake接收等-the simulation graph of DS-UWB,it includes the BER and pulse generation,ook and bpsk modulation and rake receiver.
mimo
- 一个4*8天线数的mimo仿真程序，采用16QAM调制解调，在平坦衰落环境下的误码率情况-a 4 * 8 the number of MIMO antenna simulation program using 16QAM modulation and demodulation, the decline in flat environment of the BER
eccnew
- 该程序可以算出未经编码和编码后的误码率，从而很清楚的表现纠错编码后系统的改善．-the program can be calculated without coding and the coding error rate, the performance is very clear after the error-correcting coding system improvements.
rsencode
- 通过编程计算ＲＳ编码前后通信系统的误码率可以很清楚的看到系统的编码增益．-programmed to calculate RS coding communication systems around the BER can clearly see the coding gain.
CDMA跳频通信子程序
- CDMA跳频通信子程序,本子程序计算CDMA跳频通信的误码率-CDMA frequency-hopping communications subroutine, the book calculation procedures CDMA frequency-hopping communications BER
2分集CDMA跳频通信子程序
- 二分集CDMA跳频通信子程序,计算2分集CDMA跳频通信系统的误码率-two set points CDMA frequency-hopping communications subroutine to calculate two set points Hopping CDMA communication system BER
各种数字调制的误码率仿真如fsk、psk等
- 不同信噪比下2FSK,2PSK,4PSK,16PSK,16QAM误码性能仿真
MAP. Matlab程序实现了MAP算法-最大后验概率算法
- 这个Matlab程序实现了MAP算法-最大后验概率算法，同时包括对算法有：卷积编码、卷积解码，BPSK，AWGN。同时绘制它的误码率和SNR(信噪比)。,The Matlab program achieved a MAP algorithm- maximum a posteriori probability algorithm, at the same time including the algorithm are: convolutional coding, convolution deco
bpsk.zip
- 再高斯信道和瑞利信道下bpsk误码率的分析,Again Gaussian and Rayleigh channels channel bit error rate analysis bpsk
BPSK_2
- 产生BPSK调制信号，通过高斯信道，接收端解调，计算误码率-BPSK modulated signals generated by Gaussian channel, the receiver demodulation, bit error rate calculation
1
- OFDM中不同信噪比对误码率性能的影响的matlab仿真的实验代码-Different OFDM bit error rate performance of SNR on the impact of the experiment code on matlab simulation
ofdm-design
- 基本的ofdm系统实现以及误码率分析（信道为高斯白噪声信道）-The realization of a basic ofdm system.(the channel is white gaussian noise channel)
OFDM
- 结合理论课讲解基于Matlab仿真OFDM信号，绘制OFDM符号星座图，时域、频域曲线； 绘制发送端、接收端低通滤波器的幅频特性； 分析AWGN信道条件下OFDM系统的误码率性能( combined with the theory of lesson based on Matlab simulation OFDM signal, drawing OFDM symbol constellation, time domain, frequency
MQAM和MPSK误符号率曲线
- MQAM与MPSK的仿真与调试以及对误码率曲线的分析(Simulation and debugging of MQAM and MPSK and analysis of BER curve)
turbo_new
- 包含完整的编译码代码和误码率仿真曲线，给出了1/10码率的情况，也可更改为其他码率(sova , logmap decoding)