搜索资源列表
L6
- 异步电动机又称感应电动机，是由气隙旋转磁场与转子绕组感应电流相互作用产生电磁转矩，从而实现机电能量转换为机械能量的一种交流电机。-Asynchronous motors, also known as induction motor, rotating magnetic field by an air gap and the rotor winding induced current interaction of electromagnetic torque, electromechanical
chenxushangchuan
- 用于转子故障振动，采集信号后，用小波包方法对振动信号进行频谱分析，比傅立叶变换更细化。-Spectrum analysis of vibration signal by wavelet packet method
guzhangzhenduan
- 之前写的关于单盘转子和轴承故障诊断的小程序-Before writing about the single-disc rotor and the bearing fault diagnosis applet
pmsm
- 基于转子坐标系下的永磁同步电机simulink仿真模型-Simulink simulation model of permanent magnet synchronous motor rotor based coordinate system
MATLAB-Transfer-Matrix-Method
- 使用连续分布质量传递矩阵法求解转子临界转速-Transfer Matrix method in Matlab
good
- 基于转子磁场定向的MATLAB Simulink仿真程序，。参数应调节好，其他问题联系球球 七九零二零九八二三 ，欢迎讨论-Based on the rotor magnetic field oriented Simulink MATLAB simulation program, the parameters should be adjusted, and other issues related to the ball seven nine zero two zero nine eight t
feixianxingzhendong_huanganji
- 学习转子振动必须看的一本基础方法大全书,内容包含了很多常用的方法-this is a fundamental reference when viberation of rotor learning
Encoder_Left_Right_A
- STM32编码器接口，电机速度测量和马达转子位置的测量-STM32 encoder
proj_rotor_dynamics
- 链式转子的临界转速和前三阶振型的计算与绘图-The calculation and drawing of the critical speed and the first three order modes of the chain rotor
windfarm_dfig
- PSCAD/EMTDC软件搭建的双馈异步发电机（DFIG）详细模型，转子侧采用定子磁链定向控制，网侧采用电网电压定向控制。-PSCAD/EMTDC software to build double-fed induction generator (DFIG) detailed model, using the rotor side stator flux oriented control, network side using the grid voltage oriented control.
ReadData
- 用于解决转子多自由度计算问题，用于计算得出所需的数据，具有很好的功效，能够解决转子运转问题-Used to solve the problem of multi degree of freedom rotor calculation, used to calculate the required data, has a very good effect, to solve the problem of rotor operation
main_channel_transition
- 用于解决转子多自由度计算问题，用于计算得出所需的数据，具有很好的功效，能够解决转子运转问题-Used to solve the problem of multi degree of freedom rotor calculation, used to calculate the required data, has a very good effect, to solve the problem of rotor operation
quest
- 计算转子分岔图，由转速变化得到转子的运动情况，并给定了一些参数-The rotor bifurcation diagram is calculated, and the motion of the rotor is obtained by the change of speed, and some parameters are given.
Stepper-motor-drive-source
- 步进电机28BYJ48型四相八拍电机，电压为DC5V—DC12V。当对步进电机施加一系列连续不断的控制脉冲时，它可以连续不断地转动。每一个脉冲信号对应步进电机的某一相或两相绕组的通电状态改变一次，也就对应转子转过一定的角度（一个步距角）。当通电状态的改变完成一个循环时，转子转过一个齿距。四相步进电机可以在不同的通电方式下运行，常见的通电方式有单（单相绕组通电）四拍（A-B-C-D-A。。。），双（双相绕组通电）四拍（AB-BC-CD-DA-AB-。。。），八拍（A-AB-B-BC-C-CD-D-
Asynchronous_mathematic_model
- 根据双馈风力发电机数学公式搭建的数学模型，需输入定子电压和经过调节得到的转子电压-According to the mathematical model of DFIG mathematical formula to build the required input voltage of the stator and rotor voltage regulated obtained
Mechanical-fault-diagnosis-method
- 经验小波变换(EWT)是一种新的自适应信号分解方法, 该方法继承了EMD 和小波分析方法的各自优点, 通过提取频域极大值点自适应地分割傅里叶频谱以分离不同的模态, 然后在频域自适应地构造带通滤波器组从而构造正交小波函数, 以提取具有紧支撑傅立叶频谱的调幅-调频(AM-FM)成分。本文将该方法引用到机械故障诊断中, 提出了一种基于经验小波变换的机械故障诊断方法, 并与EMD方法进行了对比分析。仿真结果表明, 经验小波变换方法明显优于EMD方法, 能有效地分解出信号的固有模态。与EMD 相比较, 该
two_level_FOC
- 针对异步电动机转子磁链定向的矢量控制系统，逆变部分采用的三电平拓扑结构，算法是采用的传统的SVPWM调制方法。-For the vector control system of induction motor rotor flux orientation, the three level topology is adopted in the inverter, and the algorithm is the traditional SVPWM modulation method.
calculation_slip
- 双馈风力发电机控制中转差的计算，输入为a相电压相位角和转子位置角。The calculation of the slip in the control of a doubly-fed wind generator is based on the phase angle of the a-phase voltage and the rotor position angle.-calculation of the slip in the control of a doubly-fed wind ge
永磁同步电机模型参考自适应simulink
- 采用以超稳定性与正性动态系统理论为基础的设计方法设计MRAS自适应律，从仿真结果可以看出，当电机从零速上升到参考转速600r/min，转速估计误差在转速的上升阶段有较大值，但随着转速上升且稳定运行后，转速误差估计逐渐减小，转子位置的估计误差也逐渐减小。
sss
- 双馈风机的仿真模型搭建，由转子侧网侧和并网运行三部分组成。-The simulation model of the double-fed fan is composed of three parts: the rotor-side network side and the grid-connected operation.