搜索资源列表
51与STM通信
- 51单片机与stm32单片机串口通讯程序文件(51 and STM32 serial communication)
67A04 uart
- 原厂对该功能是隐蔽的，如有需要可以参考使用附件的软件，串口对应的IO口为P16和P17(The original factory is covert to this function. If necessary, you can refer to the software that uses the attachment. The serial port corresponding to the IO port is P16 and P17)
FileRecv
- 51单片机，串口发送数据。用于单片机串口间数据传送交流(51 singlechip, serial port to send data)
51单片机C语言各类程序大全
- 51单片机的各类操作例程，流水灯，数码管，按键，矩阵，电机，LCD模块,AD/DA，串口，红外，TFT彩屏，NRF905无线模块等等。(51 microcontroller various operation routines, water lights, digital tubes, keys, matrix, motor, LCD module, serial port, AD/DA, IR, TFT color, NRF905 wireless module etc..)
51单片机与蓝牙模块的串口通信
- 51单片机与蓝牙串口通信，CP端串口调试助手实现，通过LCD1602显现。(51 SCM and Bluetooth serial communication)
lesson11_4
- 基于51单片机实现UART串口通信 C语言版(UART serial communication realized by 51 single chip microcomputer)
uart_printf
- 基于89c51单片机的printf语句串口文本输出程序(Based on 89c51 single-chip printf statement serial output program)
51常用汇编程序
- 51汇编程序 包括ADC、DAC、串口、1602、12864程序(assembly; assembler; collection; compile; collect and edit timer; keyer; intervalometer; timing device)
SI4463串口透明传输程序和上位机程序
- 51单片机实现对无线模块的数据传输。上位机程序(The primary states of the Si446x are shown in Figure 6. The shutdown state completely shuts down the radio to minimize current consumption. Standby/Sleep, SPI Active, Ready, TX Tune, andRX tune are available to optimize the
lanya
- 51单片机的第二串口跟蓝牙通信，实现手机蓝牙与单片机通信(51 MCU second serial port with Bluetooth communication)
51计数器--中断串口-51
- 基于C语言stc51单片机中断计数，at24c02 eeprom掉电保护，串口输出数据(Interrupt count, with power-off protection, serial output data)
串口通信
- 51单片机串口通信代码，无需修改直接用，keil(51 single-chip serial communication code, no need to modify the direct use of keil.)
notes_20171205091629
- 实现51单片机与电脑的串口通信，单片机发送，电脑接受到返回数据(Realize the serial port code of the single chip computer and the computer)
51单片机与电脑串口通信的C程序
- 单片机和电脑串口的通信例程。用c进行编写的(A communication routine of a single chip computer and a computer serial port)
基于51单片机的上位机通讯系统说明书
- 本次设计就是来完成由上位机通过串口控制来实现，以发光二极管的发光状态模拟开关电路的通断，用上位机的DOS命令对其进行控制。并用LED屏显示程序的传输。(This design is completed by the host computer through serial port control. The LED switch's luminous state is used to simulate the on-off of the switch circuit, and the upper
UART
- 这是个51单片机的串口调试实验，包括串口的初始化，串口的使用。(This is a 51 MCU serial debugging experiment, including the serial port initialization, the use of serial port.)
51黑论坛_STM32-串口输出MPU-6050
- 在STM32F103平台上使用USART收发器与电脑进行通讯(Use the USART transceiver to communicate with the computer)
51单片机蓝牙小车
- 51单片机蓝牙小车，采用lm298驱动两路电机，上位机采用手机蓝牙apk进行与小车进行串口通信，小车速度可控，采用PWM方式。手机端app以及全部工程代码都在压缩包里(The basic course of 51 single chip Bluetooth Car)
51UART
- 51单片机的串口实现printf，printf自己修改的，系统printf不好用，来源：51hei(51 singlechip serial port realization printf, printf itself modified, the system printf is not good, source)
程序
- STC12C5A60S2来完成AD采样，量化编码，同时另一路使用滞后比较器计算频率，将被采样信号存储到一个定义的BUFF内，并上传到串口屏，来显示被测波形(STC12C5A60S2 completes the AD sampling and quantization coding, while the other uses the lag comparator to calculate the frequency. The sampled signal is stored in a define