搜索资源列表
RS485
- TMS320F2812的DSP使用RS485串口进行数据通信的程序,调试通过,可用-On TMS320F2812 DSP using the RS485 serial port for data communication procedures, debugging, available
2812dsp-uart
- 基于DSP 2000开发的串口通信程序,收发都有,经测试可用-serial communication program development, tested available for DSP 2000
DSP28335_SourceCode
- DSP例程,包括简单的串口通信和电机控制等等,很有价值哦-DSP routines
AMmodemdemodem
- 用于在ccs simulator平台 对tms320c5402dsp实现对am调制与解调,程序对mcbsp多缓冲串口进行了软模拟,利用DMA传输和中断,对学习dsp的初学者有很大参考价值-this program is applied to AM modulation and demodulation in DSP C54x chip. and achieves data transmission control between program and data space.
SCI
- DSP实现串口异步通信的程序,叫你如何对SCI进行设置,定义。-DSP serial asynchronous communication procedures, tell you how to set up SCI defined.
myuart
- 使用verilog语言编写的异步串口模块,带有16级深的FIFO,它与DSP28335的SCI相似,可以帮助初学者更快地理解FPGA和DSP的硬件结构和编程思路-Use verilog language of asynchronous serial port module, FIFO with deep level 16, it was similar with DSP28335 SCI, can help beginners to understand faster the FPGA and
board1_3_bak
- TI TMSF2802 DSP实现AD采样与串口通信-using RS485 communication port to transfer data sampled by AD of TI TMSF2802 DSP
test-0221switch2
- DSP2812 SCI 与上位机串口通信源码-DSP SCI serial communication source
RS232-to--labview-
- labview接受下位机串口上传的 数据,被动接收!-labview serial port to accept the DSP of data uploaded and passive reception!
Echo
- BF548 串口中断的驱动程序。使用环境为VisualDSP++ 5.0 ADDS HPUSB-ICE。电脑上面输入的字符,通过串口发送到dsp板,dsp板接收到字符以后产生响应中断,将接收到的字符回传给电脑。-Example demonstrates how to use interrupt driven UART device driver.Characters typed in at the computer are echoed back using the chained datafl
Sci01
- C编写的基于DSP的简单串口通讯程序,C编写的基于DSP的简单串口通讯程序-Written in C, DSP-based serial communication simple main program
scia_loopback_interrupts
- DSP TMS320F28335 串口测试 中断方式-DSP TMS320F28335 serial port test interruption
VMD642_uartio
- UART 测试 本例程在 VMD642_uartio 中。 VMD642-C卡中有两路 UART 接口,在本例中,UART 的接口标准配置为 RS232,波特率-9600,数据位-8,校验位-None, 停止位-1,采用查询工作方式。 在目录 Win32\serial 下提供一个串口调试器.exe,注意设置正确的波特率。 用开发板随带的串口线将 DSP 开发板的串口和计算机串口连接好,启动串口调试 器.exe,设置串口参数,然后打开串口,就可以在发送窗口发送
MCBSP
- 介绍了DSP中MCBSP的串口通信及寄存器的设置,以TMS320C54X为硬件单元-MCBSP introduced in DSP serial communication and register settings to the hardware unit TMS320C54X
CH395
- CH395 是以太网协议栈管理芯片,用于单片机系统进行以太网通讯。 CH395 芯片自带10/100M 以太网介质传输层(MAC)和物理层(PHY),完全兼容IEEE802.3 10/100M 协议,内置了PPPOE、IP、DHCP、ARP、ICMP、IGMP、UDP、TCP 等以太网协议栈固件。 单片机系统可以方便的通过CH395 芯片进行网络通讯。 CH395 支持三种通讯接口:8 位并口、SPI 接口或者异步串口,单片机/DSP/MCU/MPU 等控制 器可以通过上述任
Sci022
- DSP2812的串口程序SCI,调试成功可以使用-DSP SCI
Monitor
- Dsp的pc端的监控程序,使用串口通信,包括变量查看,内存查看,打印-Monitoring program Dsp PC side, the use of serial communication, including the variable view, memory view, print
mcbsp
- dsp多通道缓冲同步串口程序,主要是解决dsp与ad50之间的串口通信问题,以及如何进行串口中断-Multi-channel synchronous serial buffer dsp procedures, mainly to resolve the dsp with ad50 serial communication between problems and how to carry out serial interrupt
AD9850-modulation-Data
- AD9850/AD9851模块是采用ADI应用最广泛的DDS(AD9850和AD9851)制作的模块。ADI的性能就不用多说了。模块主要参考AD9850和AD9851的资料做的。 主要功能特点: * 模块能够输出正弦波和方波,2个正弦波和2个方波输出。 AD9850: 0-40MHz AD9851: 0-70MHz 频率在20-30MHz后谐波越来越大,波形会越来越不干净。 方波: 0-1MHz * 采用70MHz的低通滤波器,使波形的SN比更好 * 并口
fft-spectrum-analysis
- 基于fft的频谱分析程序.硬件由dsp实现,数据通过串口送至计算机进行频谱分析显示。-Fft spectrum analysis procedures based on the hardware by dsp, spectral analysis of data sent to the computer through a serial display.