搜索资源列表
FPGA-FPGA-serial
- FPGA 串口通信程序,调试通过绝对好使,与大家共享,适合初学者-FPGA serial communication program, debug, so that by the absolute, and share, for beginners
FPGA--VerilogFIFO
- FPGA串口通信程序 基于fifo读写的串口通信程序-FPGA serial communication program is based on the serial communication program to read and write fifo
FPGA
- FPGA串口通信 Verilog -FPGA UART uartFPGA UART
FPGA-Uart
- fpga串口通讯程序。用Verilog语言编写-fpga serial communication program. Verilog
FPGA-chuan-kou
- 采用VHDL语言编写的可编程逻辑器件FPGA串口处理程序,实用方便,适合FPGA初学者使用。-Programmable logic device FPGA using VHDL language serial port handler, practical and convenient for FPGA beginners.
FPGA
- FPGA串口驱动,用于FPGAV5开发板上的串口驱动-FPGA USB DRIVER
FPGA--uart
- FPGA串口通信源码,通过Verilog来实现功能,新手可以参考下-FPGA uart
fpga-verilog-my_uart
- FPGA串口通信,另一种方法,总共用了三种方法,请点击用户名查看,总有你满意的-FPGA Serial communication
uart_test
- 基于FPGA 的sparten-6 AX-309片内串口uart通信例子(FPGA sparten-6 AX-309 uart connection example)
kehshechenxu
- 编制一全双工UART电路,通过试验箱MAX202E转换成RS232电平,与计算机进行通讯实验,设置8个按键,按键值为ASIC码“1”~“8”,通过串口发送给计算机,在计算机上显示键值,同时在数码管最高位显示;计算机可发送“0”~“F”的ASIC码,FPGA接收后在数码管低位显示0~F。通过按键可设置波特率。 要求:波特率为三种 1200、2400、9600,由1个按键选择,3个LED分别指示; 数据格式为1位起始位、8位数据位和一位停止位; 上位计算机发送接收软件可使用
频率接收
- STM32F103与FPGA的串口通信,波特率4800,采用单向通信的方法。(Serial communication between STM32F103 and FPGA)
IIC读写EEPROM发送到PC串口
- 能实现用IIC读EEPROM并且将读取的数据通过串口发送到PC端,以及在PC端通过串口发送数据给FPGA,再利用IIC将数据写入EEPROM(The program can realize that FPGA read the data from EEPROM by IIC and then send it to PC by UART,and that PC send the data to FPGA by UART and then write the data to EEPROM by
uartverilog
- FPGA利用串口、FIFO实现串口收发数据(FPGA using serial port, FIFO serial transceiver data)
UART-Altera
- 使用Atera FPGA CycloneII 实现串口通信,遵循RS232协议。FPGA上的模块实现了数据的接收,取补码和发送。(Achieve serial communication with FPGA, following the protocol of RS232.)
uart
- FPGA串口通信能在实现字符数据传输,与stm32中的串口通信类似(FPGA serial communication, in the realization of character data transmission, and STM32 serial communication similar)
UART_TEST
- 通过设置串口的波特率、起始位、检验位等参数,进行FPGA的串口通讯(By setting the baud rate, the starting bit, the test bit and other parameters of the serial port, the serial communication of FPGA is carried out)
uart_2_pc
- 实现FPGA和PC通过串口传输数据,已经通过验证,可以结合自己的设计直接拿来用(ealize FPGA and PC to transmit data through serial port)
FPGA实现串口解析
- 用verilog语言不同的编写方式来 实现各种复杂串口通讯(use the verilog to uart)
parameter_uart_rx
- 串口接收模块,可以通过parameter,参数化配置传输速率、传输位宽和校验。采用Verilog语音编程实现。使用者根据串口的要求配置好参数,并根据缓冲的大小配置FIFO就可以使用。对帧错误(停止位不为高),检验错误和读FIFO超时(FIFO满的情况下,有新的数据到)等现象进行了检查。(UART serial receiver module, through parameter, configuration parameters of the transmission rate, Data wi
UART_E6
- 用于测试FPGA串口接收,带singelTap。便于观测。(Used to test the FPGA serial port reception, with singelTap. Convenient observation.)