搜索资源列表
shit
- 利用触发角使得IGBT导通，它是一个用PSCAD软件实现电力电子功能的有效例子，谢谢大家的评价-Making use of the firing angle IGBT is turned on, it is a valid example of an implementation of power electronic functions with PSCAD software, thank you for your comment. . .
pmsg-IGBT-RSC-GSC-chopper
- PMSG wind with fault ride through
IGBTdaten
- IGBT.m 电器仿真中有用的东西，包括m文件及参考文献。-IGBT.m electrical simulation useful things
Buck
- 使用matlab仿真的一个buck降压斩波电路，将带有PI控制器的电路与无PI控制器的电路响应做对比。其中PI控制器采用的是使用S函数编写的控制器，进行简单的修改就可以在仿真中实现专家PI控制等等，控制器的输入参数有Kp，Ki以及控制器输出的上下限定值。因为控制器直接控制的是PWM的脉冲宽度，所以控制器的输出值限定在0到100之间。MySource用来将要求的电压与电源的电压100v进行对比，从而输出相应脉冲宽度的PWM波形给IGBT。-A Buck circuit based on matla
hvdc-wind
- IGBT HVDC wind with induction generator
PMSM_SMO22
- Self-Sensing Control of a Direct-Drive PMSG Wind Turbine System Fed by IGBT Converters.
ThreePhaseInverterUsingPWMgenerator
- DC-3 phase AC is generated by too many techniques ,one of them is using PWM generate which is going to generate 6-pulse which we will give to the IGBT/Diode . Hence , 3-phase is obtained at load
designer-of-BLDC-control
- 应用MC33035、MC33039、IGBT专用驱动模块2ED300C172-S、IGB T 功率模块FF450R12IE4以及带有 CAN (controllers area network) 接口的PIC18F458 单片机构成360V无刷直流电机闭环调速控制与通信系统 ,该电机控制器能够实现对120 kW无刷直流电机的闭环控制 , 具有过电流、欠压、过热等保护功能. 另外,还提出了CAN总线通信方案-Application of MC33035, MC33039, IGBT driver
f_20030225100244
- IGBT MOSFET COmparison
DualPulse
- 可在STM32F1X上直接运行的双脉冲发生程序，可输入电平控制脉冲，可发正负两种脉宽可调的脉冲供IGBT上下管测试，-Double pulse can be run directly on STM32F1X occurrence procedures, input level control pulse, can send both positive and negative pulse width adjustable up and down for IGBT test tube,
spwm
- 利用Matlab软件中Simulink和Power System为一个三相电压源SPWM逆变器建立系统仿真模型,并对其输出特性进行仿真分析。 它的主要功能是将直流电压变换成交流电压,采用SPWM控制策略,实时地调节逆变输出电压的幅值,以满足实际的要求。系统的主回路选用IGBT作为开关器件,为了减少输出电压的谐波,逆变电源输出接有串联谐振滤波电路。 -simulation of a spwm Inverter
Power-electronics
- Power electronics folder with simulation of boost convereter, full wave bridge rectifer with igbt
IR2103
- 该芯片是用于H桥电路，通过变化的占空比对电机进行控制。-The IR2103(S) are high voltage, high speed power MOSFET and IGBT drivers with dependent high and low side referenced output channels.
signal1
- PWM层叠载波信号，适用于基于IGBT的5电平模块化多电平换能器-PWM stacked carrier signal, suitable for IGBT based 5 level modular multilevel transducer
IGBTapplyModel-(2)
- Simulink中的仿真模块IGBT应用举例-IGBT block apply example in Simulink
power_active_filter
- The circuit models a standard shunt AHF with IGBT inverter and series inductor on the AC side and DC capacitor energization. The load consists of two diode rectifiers which are phase-shifted by 30 degrees. The Delta-Y connected rectifier is connected
Inverter1
- single phase H bridge inverter using IGBT
diode_3level_IGBT
- matlab中，计算基于二极管钳位型三电平逆变器的损耗计算。通过改变输入主电路参数，实现不同工况下的损耗计算。-matlab mfile，used to the power loss calculation of three level IGBT inverter bridge under different condition。
T_3level_IGBT
- 基于IGBT的T型三电平逆变器在不同工况下的损耗计算，改变输入参数，即可获得相应结果。-matlab mfile，used to the power loss calculation of T-type three level IGBT inverter bridge under different situation
PWM_IGBT
- this file describe how to pilote IGBT with PWM