搜索资源列表
00990_demo
- 基于51单片机的OLED(维诺)显示驱动例程。单片机可以通过IIC、SPI的通用的串行口让OLED显示想要的图形或汉字。-51 microcontroller based OLED (Vino) display driver routines. SCM through IIC, SPI universal serial port allows OLED display graphics or characters you want.
930
- oled的点亮demo程序,基于keil3的开发环境,能够点亮ssd1306芯片的oled模组-light the oled and the interface is iic,the environment based on keil and 51
I2C_OLED
- 移植原子哥的oled函数,用于LPLD函数库驱动IIC接口oled显示屏代码。-Brother oled transplant atomic functions for LPLD library drive IIC interfaces oled display code.
0.96-IIC参考
- 用于一块较简单的I2C 串口OLED例子和原版说明(Used for a relatively simple I2C serial OLED example and the original explanation)
三路超声波
- 使用STC15单片机捕获三路超声波来测算距离,并且显示到IIC接口的OLED屏幕上面(Three channel ultrasonic ranging is captured)
实验12 OLED显示实验
- 硬件资源: 1,DS0(连接在PF9) 2,串口1(波特率:115200,PA9/PA10连接在板载USB转串口芯片CH340上面) 3,ALIENTEK 2.8/3.5/4.3/7寸TFTLCD模块(通过FSMC驱动,FSMC_NE4接LCD片选/A6接RS) 4,按键KEY0(PE4)/KEY1(PE3) 5,24C02(IIC连接在PB8/PB9上面) 实验现象: 本实验通过KEY1按键来控制24C02的写入,通过另外一个按键KEY0来控制24C02的读取
OLED测试程序
- Nodic 51822 开发板调试程序,关于OLED屏的IIC通讯调试(NRF51822 OLED debugger)
esp8266_deauther-master
- arduino编程的wifikiller 使用芯片组为ESP8266 系列(12N/12F等);可以为外接显示屏,OLED 屏幕IIC接口,VCC-3.3 GUN-G,SDA,SLC接口代码中可随意修改,使用前下载好库文件,arduino库中有。(Arduino programming wifikiller uses chipset as ESP8266 series (12N/12F, etc.); it can be modified for external display, OLED s
1_开发板例程_Ver2_1
- MM32开发板活动资料 1 个标准的 JTAG/SWD 调试下载口 1 个电源指示灯(蓝色) 2 个状态指示灯(DS0:红色,DS1 :绿 色 ) 1 个 IIC 接口的 EEPROM 芯片,24C08,容量 1024 字节 1 个 SPI FLASH 芯片,S25F008A,容量为 1M 字节(即 8M bit) 1 个标准的 2.4/2.8/3.5/4.3/7 寸 LCD 接口,支持触摸屏 1 个 OLED 模块接口(与 LCD 接口部分共用) 1 个
中景园电子0.96OLED显示屏_STM32F103C8_IIC_V1.0
- 0.96寸OLED屏幕 IIC接口的驱动显示程序(A drive display program for the 0.96 inch OLED screen IIC interface)
5529_key_pwm_ad_oled_1.1
- 针对MSP430F5529的单片机例程,IIC接口引出PWM输出,OLED显示(For msp430f5529 microcontroller routines, IIC interface leads to PWM output, OLED display)
I2C—0.96寸OLED
- 基于stm32f103的0.96OLED显示例程,iic 通讯协议。(0.96 OLED display routine based on stm32f103, IIC communication protocol.)
BMP280SensorSPIOledDis
- 使用Arduino Mega2560控制IIC总线的BMP280模块来检测气压值以及温度并显示到OLED上面(How to use Arduino Mega2560 Control BMP280 to get atmospheric pressure and temperature,in the last diplay them in OLED module)
串联型稳压电源
- 基于STM32F103的串联型稳压电源。普中的红外遥控输入设定电压, (SPI)TLC5615DA输出作为基准电压,AD用ADS1115,(IIC)OLED显示电压、电流。过流保护。输出0-12V。 附件包含原理图+程序+红外遥控按键说明(Based on STM32F103 series regulated power supply. The infrared remote control input set voltage, (SPI) tlc5615da output as the ref
软件模拟I2C
- 基于IIC控制的OLED屏幕通过软件模拟
stm32 c8t6 oled和ab相脉冲计数
- 4线iic屏,有OLED的汉子字库,自己取值可更换,可以测ab相pwm波脉冲数,每个定时器的捕获模式都写了,自己开发时写的小测试板,寄存器的,有注解,想要库函数的留言