搜索资源列表
SCommTest
- 一款根据特殊需要自制的串口调试助手。源码中是为了与MSP430通信完成对ADXL345的数据采样分析,可根据需要进行更改。-A home-made according to the special needs of the serial debugging assistant. The source of a ADXL345 the data sampling analysis completed in order to communicate with the MSP430 can make
MSP430-RS232
- 基于PC与单片机间的RS232通信,实现信息的交互,其中,PC为主机,通过RS232电缆多头与从机MSP430连接,即一台PC机可访问各台从机,对每台从机的访问是通过对从机设置不同的地址来实现的,每台从机处于监听状态,程序上来说就是每台从机在此时只接受地址信息,并与自己的地址进行匹配,如果匹配一致,则此时这台从机程序设计时便可识别数据信息,此时PC主机便可通过传输特殊命令数据实现对单片机“发号施令”,是MSP430单片机执行主机想让做的事,这便是基于PC机的多机通信来实现实践中某些控制的基础。-
MSP430-UART
- MSP430G2553 单片机的UART的通信程序,调试已通过-The microcontroller UART MSP430G2553 communication procedures, debugging has passed
nRF2401A-MSP430
- 基于msp430f149的无线通信测试程序,百分百测试通过,这个是我买的开发板上自带的。用的是433Mhz的模块NRF2401A-Msp430f149 based wireless communications test program, full test, this is what I bought development board comes with. Using a 433Mhz module NRF2401A
msp430-interface-to-cc1100
- msp430与cc1100的接口程序,是无线通信设计的基础。-msp430 and cc1100 interface program, wireless communications design.
MSP430-SPI
- msp430f149 spi通信,用户可以通过SPI的发送和接受中断标志位来完成协议的控制。-msp430f149 spi,MSP-FET430P140 Demo- USART0, SPI Full-Duplex 3-Wire Slave P1.x Exchange
MSP430-MODBUS
- 430 MODBUS 代码 modbus 源代码,RS485 通信,实现RTU通信-430 MODBUS code modbus source code, RS485 communications, RTU communication
cycloneiii_3c16_signal
- 基于FPGA,DDS原理的双路正弦波信号发生器,含有与msp430通信模块程序。-Based on FPGA, DDS principle of dual sine wave signal generator, communication modules contain msp430 procedures.
GenericApp-msp430
- CC2530单点通信程序,这是官方权威知道程序-CC2530 single-point communication program, which is the official authority to know the program
STM32-MSP430-SI4463-code-SI4432
- 程序的功能: STM32实现的SI4463程序代码, 是2GFSK调制,频率433MHz,功率20dBm,已经最大。 SI4463程序还带有读取RSSI,功率调节的功能,都把数据通过串口输出。如果要做运动检测,定位,RSSI可以用到。 RSSI是接收到的信息强度指示,当距离远时,信号强度低,可以根据信号强度做一些声音报警。 STM32实现SI4432通信,是GFSK调制,频率433MHz,功率20dBm,已经最大。 实现功能:主机通过发送指令给从机,从机收到数据以
通用MSP430—I2C程序
- 利用msp430的通用I/O端口模拟I2c协议的源代码,利用此代码可以不需要I2c模块即可进行I2C通信-use of the Controller General I/O Ports I2c agreement simulation source code, the use of this code can not I2c module can hold I2C communications
RS485-MSP430
- MSP430F149单片机程序,实现RS485通信,DM430-A开发板测试成功-RS485 Communication Based On MSP430
Communication-with-the-rs485-msp430
- 该程序用于msp430与rs485的通信的测试-Communication with the rs485 msp430
IIC-msp430
- 面向msp430x2x系列硬件I2C的使用以及对24c64的通信.内涵可用程序库以及主函数克直接使用。-Msp430x2x series for use and hardware I2C communications. Connotations of available libraries and the main function of gram 24c64 directly.
msp430
- msp430g2553与上位机之间的通信远程序,实现了mspg2553 与上位机之间的通信-The communication between msp430g2553 and host computer procedure far, realize the communication between mspg2553 and host computer
msp430-and-ADXL345-
- msp430与ADXL345的I2C通信c语言程序-msp430 I2C communication with the ADXL345 c language program
msp430
- 1.机架是上一届准备国赛前买的,电机是空心杯(2000转/min) ,电池是11.1V的航模电池 2.采用2块msp430f149最小系统做飞控板,一块用来姿态控制,一块用来完成题目要求,两者之间通过串口通信 3.陀螺仪用的是MPU9150(九轴),自带有地磁传感器,不需要再加地磁传感器 4.数据融合是靠MPU9150的内部DMP处理输出(该部分程序时移植32单片机的,针对430的时钟频率对该部分程序做了一些调整) 5.姿态控制算法是PID-1 rack is the last
serial4
- linux串口与msp430通信程序源码-linux serial with msp 430 mcu connection
MSP430-Timer_A-simulate-uart-
- MSP430 TimerA 模拟uart串口通信-MSP430 TimerA uart
MMA845aSI4463aGPRS-MSP430-
- 加速度传感器控制通信源码,加速度芯片MMA845,无线短距离通信,modbus协议-Acceleration sensor control communication source