搜索资源列表
基于FPGA的数字信号显示系统软硬件设计
- 该文阐述了现场可编程逻辑器件FPGA的主要特点,应用FPGA芯片和VHDL硬件描述语言设计的模拟示波器数字信号显示系统的设计原理和设计方法。-this paper, the field programmable logic devices FPGA main feature FPGA chip and VHDL hardware descr iption language design analog signals to digital oscilloscope system design pr
2410DA
- 2410开发板在ADS下的D/A转换测试程序。 运行步骤: 1 打开DA.mcp工程文件 2 运行 3 使用示波器, 连接示波器与开发板上的DA输出和地线, 观察示波器上的变化 文件说明: ad_test.c 开发板初始化文件 ad.c ad实验主程序文件 -2410 ADS development board in the D / A converter testing procedures. Running steps : an open DA.mcp
EST406计算机数据采集与软件系统
- 连续记录器:任意通道显示;多种时间尺度显示;不丢点连续采集、显示; 全功能的双踪示波器:任意通道中选择显示1~2通道;支持模拟量、开关量;任意放大倍数;锁相功能;波形运算功能;波形局部细化功能;超快速波形显示; 支持模拟量、开关量、脉冲量、频率、热电偶、Pt电阻等多种信号的采 -consecutive record : random access display; Multiple time scale display; Do not lose points for
OscilloChart
- 主要是实现类似示波器显示波形的功能,可以设置一些参数-mainly achieve similar oscilloscope waveform display function can set some parameters
SSA615
- 文档是关于WBDSO中源码的过程解释,程序是用VC++实现的,界面是一种示波器的形式。 功能是对方波,正弦波和三角波进行统计分析。-WBDSO documentation on the process which source explained that the procedure is used VC, oscilloscope interface is a form. The other function is to wave, sine wave and triangular wav
keyboard_input_v1.02
- matlab键盘输入模型程序,用simulink制作。在7.0以上版本直接运行 运行过程中按一下键盘就会看到示波器上出现一个脉冲信号。-Matlab keyboarding model procedures used Simulink production. In version 7.0 to run over the course of operation under the keyboard will see what appeared on an oscilloscope pulse
jiandanshiboqi
- 采用定时器编写的简单示波器 很有参考价值-prepared using a simple timer oscilloscope great reference value
gpib1
- 广泛用于示波器上的gpig工业标准接口的计算机编成库-widely used oscilloscope gpig the industry standard interface for the computer organization
specanal
- 基于matlab的通信系统仿真系列。A simulated oscilloscope and a simulated spectrum analyzer。供刚接触到matlab通信系统仿真的朋友使用。-Matlab-based communications system simulation series. A simulated oscilloscope and a simulated spect rum analyzer. Matlab for the counting of the com
CVI2
- 利用CVI制作虚拟示波器,比传统示波器更易使用,且可以自己更改功能。-produced using CVI virtual oscilloscope than traditional oscilloscope easier to use, and can change their function.
dailvboshiboqi
- 用NI公司的labview7.1编的一个程序。 本程序可以使用dmm设备采集数据信息,然后通过界面显示(类似示波器),而且,加入了滤波功能,能够自行选择滤波函数,显示滤波后的波形。-using NI companies labview7.1 a series of procedures. This procedure can be used for data acquisition equipment DMM information, then pass the interface show
FIR123
- 1.利用Matlab进行产生频率为1000Hz和6000Hz的正弦信号,利用FDATOOL设计FIR滤波器(fs=16000Hz),以滤波6000Hz分量,并利用SPTOOL工具对信号滤波进行仿真与验证。 2.从MIC端口(J5)输入频率为1000Hz和6000Hz正弦信号的叠加信号,编写实时FIR滤波程序,选择合适的滤波器参数,滤除6000Hz的频率分量,利用示波器在SPEAKER端口(J6)观察输出波形。分析信号的频谱结构,设计满足要求的数字滤波器,-1. The use of Matl
TIMER123
- 1.可组合给定内容的程序,利用示波器测量XF或LED0管脚的信号频率。 2.可修改定时器中断服务程序,使三个发光极管每隔1秒钟轮流点亮一次。-1. Portfolio will be content to the procedure, and use oscilloscope measurement XF or LED0 pin signal frequency. 2. Amend timer interrupt service routine, three-top every one li
cosinexp123
- 1.分别利用计算法和查表法产生1000Hz的余弦波信号,并使用示波器观测产生信号的频率和幅度。 2.利用计算法产生其他非正弦类周期信号波形,如周期矩形波、三角波、锯齿波等。-1. Each calculation method and the use of look-up table method have 1000Hz the cosine wave signal, Oscilloscope observation and the use of the generated signal f
lecoryscope
- lecory示波器的remote control函数,可以设置示波器的各种参数,也可以从示波器得到数据.-lecory Oscilloscope remote control function, oscilloscopes can set the parameters, can also receive data from the oscilloscope.
sbqdll
- 示波器的源代码 虚拟仪器开发的实例 是界面模版,不包含数据采集-oscilloscope source Virtual Instrument Development example is the interface templates do not include data acquisition
cpubbs_soundcard_oscillograph
- 基于LV的数字示波器设计。。。。。。那要那么多字做什么。晕死我了-based on the digital oscilloscope LV design. . . . . . This will be so many characters and so on. Olympus me Gangan Khan
xunishiboqi
- vc+编的虚拟示波器,源代码,说明什么都有喔,可以看看喔.-vc series of virtual oscilloscope, source code, what is oh, oh look.
m8usb
- 一个基于Visual Basic编程的8通道虚拟示波器,有源代码,好好看喔-a Visual Basic Programming 8-channel virtual oscilloscope, the active code, Kano good! !
SBQ
- 示波器程序 经过调试完全可以运行 供大家交流心得使用-oscilloscope after debugging procedures can run for the exchange of ideas we use