搜索资源列表
cantilever-beam
- ansys悬臂梁模态分析，命令流大全，受力分析及加载-cantilever beam ansys modal analysis, command stream Daquan
a2
- 桥梁工程中的拉梁考虑实体钢筋非线性的ANSYS程序，是变截面梁。-Bridge Engineering pull steel beam considering nonlinear ANSYS program entity, the variable cross-section beam.
20111129-(2)
- ansys 张弦梁结构 木结构 非线性有限元 分配加载-ansys 张弦梁
optimal-design
- 用ANSYS对梁进行优化设计，分为优化分析文件，优化控制文件，求解方法几个方面。-Using ANSYS to optimize the design of the beam, divided into optimization analysis files, optimize the control file, the method for solving aspects.
beam4_solid45
- ANSYS建模solid45，用于建立梁模型并且与beam单元想耦合-The ANSYS modeling SOLID45 used to establish the beam model and beam unit want to coupling
S-1
- ansys预应力混凝土梁的非线性分析，破坏分析-failed to translate
exam3_2
- 受纯弯曲的梁的matlab有限元计算源程序，配套书籍是《ansys分析与matlab编程：徐荣桥》-Pure bending beam source matlab finite element calculation, matching books ansys analysis and the matlab programming: Xu Rong Bridge "
bridge
- ansys分析变截面连续箱梁桥的命令流,包括建模，求解，和模态分析等-ansys analysis of variable cross-section continuous box girder bridge command stream, including modeling, solving, and modal analysis
Beam
- ANSYS参数化语言写的计算悬臂梁自由振动振型图的程序！-APDL code for Beam Vibration
siyu
- ANSYS 双片箱型梁的建模，分析应力和变形量-ANSYS modeling of two-piece box beam, the amount of stress and deformation analysis
box-girder-beam3
- Ansys 中变截面连续箱梁建模，静力分析，模态分析以及设计弯矩绘制，影响线的绘制等。-Variable cross-section continuous box girder model in Ansys, the static analysis, modal analysis, and design bending moment, influence line drawing, etc.
moving-loads
- Ansys命令流求解移动载荷作用下梁的动态响应问题，可根据实际问题修改参数。-The dynamic response of beam Ansys command flow solution under the action of moving loads, you can modify the parameters according to the actual problem.
dayin
- 有限元分析中T形梁截面的命令流文件，无需建立梁的模型，直接生成梁的图形-ANSYS finite element analysis of T beam section of the command stream file does not need to establish the model of the beam, the beam generated graphics
xuanbiliangshouzhonglibianxing
- 悬臂梁受重力作用产生的大变形以及它的固有频率，这是在ansys中的命令流编程，可以看看。-Izod produced by the gravity of large deformation as well as its natural frequency, which is ansys commands dataflow programming, you can see.
Shell-Beam
- APDL板梁组合建模()
对比试件JD0
- 主要是用来写剪力墙的低周反复试验，很不错关于节点的对比震损，ansys命令流用于做抗震分析的。特别详细。特用于研究。(It is mainly used to write low frequency cyclic tests of shear walls. It is very good about the comparative seismic damage of nodes, and the ANSYS command flow is used for seismic analysis. E
NEW continuous bridge
- 连续梁桥ansys静力分析命令流，你值得拥有！(ANSYS static analysis command flow for continuous beam bridge)
一端铰接一端自由梁振动
- 一端铰接一端自由梁振动的ANSYS程序与仿真结果.(Vibration of a free beam with one end articulated and one end free)
瞬态动力学分析
- 三个ANSYS瞬态分析的命令流：冲击载荷作用悬臂梁的阻尼振动分析；破碎锤的瞬态动力学分析；滑动摩擦接触分析(Three command streams of ANSYS transient analysis: damped vibration analysis of cantilever beam under impact load; transient dynamic analysis of crushing hammer; sliding friction contact analysis)
模态分析命令流
- 利用ansys apdl对梁进行模态分析(Modal analysis of beams with ANSYS APDL)