搜索资源列表
denghefengmingqizonghe
- 蜂鸣器与LED结合，请有兴趣的自己下载-Buzzer and LED combination, please download their own interest! !
Ex19
- STC单片机，程序功能：开机后,LCD倒记时显示，开始LCD上显示9,1秒钟减1,直到减到0时,蜂鸣器响.停止。 学习重点: 1、模块间的交互 2、LCD、定时器的应用-STC microcontroller, the program features: boot, LCD countdown display, LCD display started by a 9,1 seconds, until reduced to 0, the buzzer sounds. Stop. Key
FREDDY
- This the code for door security. It will use a keypad with LCD to enter the code for door entry. Buzzer sounds to for wrong password entered. It ll sound non-stop if it is entered more than 3 times.-This is the code for door security. It will use a k
MINI2440_PWM_TEST
- MINI2440裸机蜂鸣器测试源代码分析-MINI2440 bare metal buzzer test source code analysis
DS18B20
- 开机时对DS18B20进行检测，如果DS18B20检测不正常，蜂鸣器报警，关闭显示。 采用6位数码管显示－用4位数码管显示温度值，2位数码管显示符号。-DS18B20 when power to detect abnormal if DS18B20 detection, buzzer alarm, turn off the display. 6-digit LED display- LED display with four temperature values, 2 digital
eer
- 使用ZLG7290与AT89C51单片机实现LED与蜂鸣器之间的结合显示 -AT89C51 MCU using ZLG7290 and integration between the LED display and buzzer
BEEP
- 基于LPC2148的仿真实例 蜂鸣器的测试 仿真器是 jlink v8-LPC2148 based on the simulation test buzzer is jlink v8 emulator
C51
- 单片机的一些基本程序，如4*4矩阵键盘，1602，中断串口通信，流水灯，DS1302，蜂鸣器，ADC0832，AT24C04，DS13B20.-SCM basic procedures, such as 4* 4 matrix keyboard, 1602, interrupt serial communication, water lights, DS1302, buzzer, ADC0832, AT24C04, DS13B20.
weijiyuanli
- 使用SHT11测温，要求用点阵LED对温度进行显示，并能通过按键对温度进行上限值设定，要求越限蜂鸣器报警... -Use SHT11 temperature, the temperature required for use of dot matrix LED display, and pass the keys to set the upper limit on the temperature, the more limited requirements of the alarm buzz
LCD
- 使用SHT11测温，要求用点阵LED对温度进行显示，并能通过按键对温度进行上限值设定，要求越限蜂鸣器报警... -Use SHT11 temperature, the temperature required for use of dot matrix LED display, and pass the keys to set the upper limit on the temperature, the more limited requirements of the alarm buzz
lcd1602
- 使用SHT11测温，要求用点阵LED对温度进行显示，并能通过按键对温度进行上限值设定，要求越限蜂鸣器报警... -Use SHT11 temperature, the temperature required for use of dot matrix LED display, and pass the keys to set the upper limit on the temperature, the more limited requirements of the alarm buzz
shizhong
- 使用SHT11测温，要求用点阵LED对温度进行显示，并能通过按键对温度进行上限值设定，要求越限蜂鸣器报警... -Use SHT11 temperature, the temperature required for use of dot matrix LED display, and pass the keys to set the upper limit on the temperature, the more limited requirements of the alarm buzz
ARM7Timerbuzzerprogram
- 这是ARM7中所编写的定时器设置蜂鸣器程序-It is written in ARM7 Timer buzzer program
(ICC)
- 以学习板蜂鸣器和EXT0按键为硬件电路 2、TC0用作计数器 3、程序模块化练习，捆绑编译的应用 4、TC0工作于计数状态，T0引脚上升沿/下降沿将使计数器加1，计数溢出后蜂鸣器 长鸣500ms。信号由按键EXT0产生 -Buzzer and EXT0 to learn key board as the hardware circuit 2, TC0 used as a counter 3, a modular training program, compile the a
Bell
- 用TMS320F2812的GPIO编的蜂鸣器程序，希望有帮助-TMS320F2812 compiled by the GPIO buzzer procedures in the hope help
music
- 51单片机用蜂鸣器放音乐的程序，音乐编码有月亮代表我的心，两只蝴蝶等-51 SCM with buzzer or music program, music encoding the moon represents my heart, two butterflies
Buzzer
- Example project for IAR 5.4. A led blinking application with C&C++.
liushuideng
- 第一个发光管以间隔200ms闪烁 8个发光管由上至下间隔1s流动，其中每个管亮500ms,灭500ms,亮时蜂鸣器响，灭时关闭蜂鸣器，一直重复下去。 8个发光管来回流动，第个管亮100ms,流动时让蜂鸣器发出“滴滴”声。 用8个发光管演示出8位二进制数累加过程。 8个发光管间隔200ms由上至下，再由下至上，再重复一次，然后全部熄灭再以300ms间隔全部闪烁5次。重复此过程。 间隔300ms第一次一个管亮流动一次，第二次两个管亮流动，依次到8个管亮，然后重复整个过程。 间
20101214
- 该抢答器是用数字显示抢答倒计时时间，倒计时可由99倒计到0，倒计开始和结束时蜂鸣器都会发出抢答成功和回答时间到的提示音。选手抢答时，在显示数组的数码管显示抢答成功的选手编号直至计时结束该数码管才不亮。-Responder is the answer in the countdown time digital display, countdown count down by 99 to 0, the beginning and end of the countdown will be issued
beepsing
- 这是一个利用单片机的定时器来操控蜂鸣器唱歌的程序，相当好玩，值得学习！-This is one of the microcontroller timer manipulating buzzer singing procedures, quite funny, it is worth learning!