搜索资源列表
CAN-building
- CAN通信源代码，包括实现及例子，keil工程！-CAN communication source code, including the realization of and examples, keil project!
CAN
- can 总线 stm32 iar for arm-can bus stm32 iar for arm
CAN
- c8051f500的CAN操作例程，包括配置，中断操作，数据发送与数据接收，很好的包括了CAN函数功能块-c8051f500 of CAN operation routines, including configuration, interrupt operation, data transmission and data reception, a good block, including the CAN function
can-self
- stm32 中的can功能调试程序，实现环回模式下can通信功能-stm32 can function in the debugger, the loopback mode can achieve the communication function
CAN
- 该例程为CAN(Normal)例程,STM32源代码，值得学习！-The routine for the CAN (Normal) routine, STM32 source code, it is worth learning!
design-of-CAN-based-on-VHDL
- 基于Verilog+HDL设计CAN控制器,详细介绍各功能模块的设计。本论文的重点是CAN总线通信控制器的前端设计。即用Verilog HDL语言完成CAN协议的数据链路层的RTL级设计，实现其功能，并且能够在FPGA开发平台Quartos上通过仿真验证，证明其正确性-Verilog+ HDL-based design of CAN controller, detailed design of each functional module. This paper focuses on the C
CAN-ceshirx
- DsPIC30F4011的CAN总线开发程序，该程序是用于CAN数据的定时发送，标准帧8字节-DsPIC30F4011 CAN bus development program, the program is used for CAN data sending, standard frame is 8 bytes
can
- 智能停车场CAN总线嵌入式脱机控制板设置程序-CAN bus embedded intelligent parking control panel setup offline
PC104-CAN-driver-VxWorks-design
- VxWorks下PC104 CAN驱动程序设计-PC104 CAN driver under VxWorks design
can
- 51单片机，SJA1000CAN控制器上CAN发送接收数据程序。通过USBCAN发送控制报文，控制直流电机转速，经调试好使。-51 single-chip, SJA1000CAN CAN controller program sending and receiving data. Control packets sent by USBCAN, DC motor speed control, so that by debugging.
can-bus
- CAN总线控制器的VERILOG工程文件,很实用，工程是ISE可以打开，也可以只使用工程里面的代码-can bus project with VERILOG
CAN
- can收发程序，NXP芯片 作can信号转发功能-can send and receive procedures, NXP chip for signal forwarding can
MSG-3C-CAN--MCP2515
- CAN控制器采用MCP2515，CAN总线循环将8个字节的数据发送出去。-CAN bus cycle will be 8 bytes of data sent, CAN controller using MCP2515
CAN
- can 程序 can.c can的主程序控制-can program
PIC16F87X-CAN
- ；*** *** ***PIC16F87X CAN通信程序**************** list p=16f877 ；定义微控制器为PIC16F877芯片 include "p16f877.inc" ；16F877芯片的寄存器定义 include "MCP2510.inc" ；MACP2510芯片的寄存器定义 ；**************寄存器与变量定义******************* TxBytes equ 0x20 ；SPI发送数据
Lab0310-Can-Self-Test
- DSP中的can通信程序，实现两个DSP之间的通信，是我自己编写的，验证成功。-The DSP can communication program, communication between two DSP, is what I have written, the validation is successful.
CAN-USB-_FIRMWARE
- 实现CAN总线的UBS接口，完成了UBS总线与CAN总线的数据传输的转换-CAN bus interface, the UBS, UBS completed the bus and CAN bus data conversion
CAN
- Stm32f103 can bus demo example-Stm32f103 can bus demo example功能开发
LPC-ARM7-CAN
- LPC ARM7 下CAN 通信 包括收发和ID过滤-LPC ARM7 under the CAN communication, including mail and ID filtering
DSP-realize-the-function-CAN
- 本程序实现两片DSP完成CAN通讯功能,并通过七段数码管的显示,内容为发送实验箱传送的数据。-The DSP program to achieve two complete CAN communication, and through the seven-segment display, the content delivery box to send experimental data.