搜索资源列表
H6152
- 电梯门禁系统，包括系统原理图和源程序。 基于AT89C52控制H6152读卡器，写Mifare卡射频夹和连接系统 主机通过CAN总线通信，CAN总线控制器SJA1000，收发器是P82C250。-Door guard system of the lift, Including systematic principle picture and source program . AT89c52 control H6152 card reader to write Mifare radio
通过串口B给DSP发送指令
- 基于dsp2812，通过串口B给DSP发送指令，通过CAN总线通讯，来控制电机控制卡-Based on dsp2812, by sending commands to the DSP serial port B, through the CAN bus communication, to control the motor control card
dsp28335code
- dsp28335的串口，CAN总线，SPI，AD转换，定时器，DMA,PWM全部例程。还包括需要的头文件。-examples of dsp28335(include CAN bus,SPI bus,AD transfer,timer,DMA,PWM and so on).Also the headers.
canbus
- 实现CAN总线的通信，并通过测试验证，用verilog在FPGA上实现-CAN bus communication, and tested to verify that, in the FPGA using verilog
iso15765
- 用于can通讯的 can 总线协议iso 15765的中文翻译，虽然有些地方不大准确，但可以对照英文一起看，方便英文不大好的同学-Communication can be used can bus protocol iso 15765 Chinese translation, although in some places is not accurate, but can be controlled in conjunction with the English, to facilitate t
CAN_RX
- F2812 CAN总线接收数据（CCS3.3开发环境下） 实验目的:通过外部其他CAN设备给Super2812发送数据，了解CAN总线的设置和通讯过程，请尤其注意ID的设置 实验说明:将MBOX16设置为接收模式，并采用中断的方式接收数据 实验结果:可以观察变量Rec_h，Rec_l,查看收到的数据-F2812 CAN-bus receiving data (CCS3.3 development environment) Purpose of the experiment:
Can_LED
- ti lm3s9b92 CAN总线使用代码，使用can总线通信的源程序-ti lm3s9b92 CAN bus using the code, use the can bus communication source
source_code.rar
- 一些源程序，主要包括CAN总线驱动、sdram VHDL实现、ucos2的移植、SDIO驱动、tcpip的实现、usb控制器代码、基于FPGA的雷达目标模拟器等,Some source code, including CAN bus driver, sdram VHDL implementation, ucos2 transplant, SDIO drivers, tcpip of implementation, usb controller code, based on the FPGA, s
CAN_C8051F500.rar
- CAN of C8051F500/F510 CAN 2.0 Bus 發送跟接收Keil C source sample code.可以用在CAN 2.x的上面喔~,CAN of C8051F500/F510 CAN 2.0 Bus sent with the receiver Keil C source sample code. Can be used in the above CAN 2.x喔~
NODE_IEEE30
- 电力系统标准测试系统，30节点系统，格式完全正确，可以方便的用来分析计算。-Power system standard test system, 30-bus system, the format entirely correctly, can easily be used to analyze the calculation.
51MCUSJA1000
- 基于51系列单片机的can总线驱动器 sja1000的驱动程序 本程序基于c8051f系列同样有用-Based on 51 Series MCU can bus drivers drive sja1000 This procedure would also be useful based on the c8051f Series
Calibration
- 一种上位机在线标定系统，系统以虚拟仪器技术为核心，融合了单片机技术，现场总线技术，实时控制技术，CCP技术。对CAN总线上的智能仪表进行全方位自动化的标定，设置，控制等。同时还可以对远程仪表在线升级，在线仿真。完成工业生产线上仪器的快速调试及集中统一管理。-Online calibration of a PC system, a virtual instrument technology at the core, the convergence of single-chip technology
CAN_SDK
- CAN总线通信的SDK，可以用于VC和LINUX下的C/C++环境。非常好用。-A SDK for CAN bus, which could be used for C/C＋＋ environment under VC and Linux. Very nice to use.
BootLoad_PeiMegaLoader
- 一个BootLoader程序和PC端的VB源代码 AVR程序是由527DZ的代码修改而来，主要修正了1个Bug，并增加了页地址效验 目标系统是M8，11.0592M，可根据需要修改，熔丝位BOOTRST要编程 VB程序只支持Bin文件，不支持Hex文件，可使用Hex2Bin工具转换，或使用烧录工具，调入后再保存成Bin文件，只是要注意长度，不要写到Boot区地址 -A BootLoader program and the PC side of the VB source code for
mcp2515
- 在LINUX操作系统下,CAN总线的实现程序-In the LINUX operating system, CAN bus implementation of procedures
canbus
- 基于ARM S3C2440的CANBUS总线的驱动程序，can 主IC为MCP2510，CAN 正负脚应该接120R 跨阻-Based on ARM S3C2440' s CANBUS bus driver, can the main IC for MCP2510, CAN feet should take positive and negative cross-resistance 120R
DMA_example
- Linux设备驱动开发DMA dreiver代码，测试成功，可以使用-DMA dreiver Linux device driver development code, the test is successful, you can use
C8051F
- C8051F的例程。包括AD、DA、比较器的编程、CAN总线等。还有单片机的应用实例-C8051F routine. Including AD, DA, comparator programming, CAN bus, and so on. There SCM Applications
CAN
- CAN总线通信的程序设计，包括CAN的初始化，CAN的中断程序等-can buscan buscan buscan buscan buscan bus
advcan_source_v2.11.tar
- 研华CAN 通信卡Linux 驱动，sja1000 CAN 芯片，支持2.4和2.6内核-advantech CAN bus linux driver, sja1000 CAN chipset, support 2.4 and 2.6 linux kernel