当前位置:
首页 资源下载
搜索资源 - dc motor microcontroller
搜索资源列表
-
0下载:
这是一个基于单片机的用VC编程的直流电机的源代码,里面有原理图-This is a microcontroller based DC motor with VC programming source code, which has the schematic
-
-
0下载:
give idae about how to control dc motor using microcontroller
-
-
0下载:
直流电机程序 开发环境 单片机编程软件。-DC motor program development environment microcontroller programming software.
-
-
0下载:
本程序通过51单片机实现了直流电机调速的功能-This procedure achieved by 51 DC Motor Speed ??Microcontroller features
-
-
0下载:
单片机编程,关于C51中直流马达功能的编写。具有实践参考的作用。-Microcontroller programming features on the C51 in the preparation of the DC motor. The role of practical information.
-
-
1下载:
基于51单片机的温度控制直流电机转速的设计 内含protues原理图及源程序-51 Microcontroller based DC motor speed temperature control design schematics and source code contains protues
-
-
0下载:
直流电动机调速基于51单片机的proteus仿真-DC Motor Speed Control Simulation Based on Microcontroller 51 proteus
-
-
0下载:
基于单片机AT89C51的直流电机PWM调速系统-AT89C51 Microcontroller based DC motor PWM speed control system
-
-
0下载:
基于C51单片机开发板的实现直流电机调速,及步进调整的C语言源程序。-C51 microcontroller development board based on the realization of DC motor speed, and adjust the C language source code stepper.
-
-
0下载:
IC AT89C51 is a low-power, high-performance, 8-bit microcontroller with 8 kB of Flash programmable and eras-able read-only memory
(EPEROM),256 bytes of RAM,32 input/output (I/O)lines, three 16-bit timers/counters, a six-vector two-level interrupt a
-
-
0下载:
This program has been written for PIC16F877 microcontroller. This program is used to control the speed of DC motor based on PWM
-
-
0下载:
用单片机输出两路PWM来控制直流电机的正反转,一般像小马达之类的,都可以,我已经调试成功!-Two PWM output with a microcontroller to control the DC motor rotating, generally as small motors and the like, can I have debugging success!
-
-
0下载:
单片机驱动直流电机的闭环控制C程序,完整的程序包-Microcontroller-driven closed-loop DC motor control C program, a complete package
-
-
1下载:
《单片机C语言程序设计实训100例——基于8051+Proteus仿真》案例压缩包 第 03 篇 综合设计 24 温度控制直流电机转速-" Microcontroller C Programming Language Training 100 cases- based on 8051+ Proteus simulation," Case No. 03 compressed package integrated design speed of 24 temperature c
-
-
0下载:
《单片机C语言程序设计实训100例——基于8051+Proteus仿真》案例压缩包 第 03 篇 综合设计 27 用DAC0808设计的直流电机调速器-" Microcontroller C Programming Language Training 100 cases- based on 8051+ Proteus simulation," Case No. 03 cabinet 27 with the DAC0808 integrated design of DC moto
-
-
0下载:
自己写的电机控制第二个:VB做的上位机通过串口向51单片机发送命定,通过L298驱动直流电机,电机反溃的信息又发回VB到VB上显示-To write the second motor control: VB to do the PC via the serial port to send commands to the microcontroller 51 set by L298 drive DC motor anti-ulcer information and send back to VB
-
-
0下载:
仅仅使用L298驱动芯片,主控为51单片机,在keil中调试测过,专门驱动步进电机的!不是直流电机。-Just use the L298 driver chip, the master microcontroller 51, in keil debugging measured before, specifically to drive stepper motor! Not a DC motor.
-
-
0下载:
光伏水泵的设计研究,内容涉及用PIC 单片机来控制直流无刷电机,其中用的的AD转换。-The design of the pump, photovoltaic content involves use PIC microcontroller to control the brushless dc motor, including the use of AD transform.
-
-
0下载:
this the circuit of dc motor with microcontroller. simple. using ewb.-this is the circuit of dc motor with microcontroller. simple. using ewb.
-
-
0下载:
单片机向LM629给初值,LM629根据所给参数开始调节直流电机转速,编码器反馈值送回LM629,重新修改参数,控制电机转速。-Microcontroller to the initial value to the LM629, LM629 began to adjust parameters according to the DC motor speed encoder feedback value back to the LM629, re-modify the parameters to
-