搜索资源列表
elevator
- 施耐德PLC控制伺服电机拖动模拟电梯厢的运行，模拟电梯运行状态-Schneider PLC control servo motor drag simulate the operation of the elevator car, simulated elevator operation status
JAVA-Elevator-control
- 5层电梯控制，包括楼层的锁定，楼层状态的更新判断，上下楼方向的判断等-5-story elevator control, including floor lock, floor status updates judgment, judgment on the downstairs direction
elevator-c
- 办公楼电梯运行系统C代码,完整实现大家随意下载-Office building elevator system running C code, the full realization of all of you to download
CAN-bus-applications-in-the-elevator
- CAN-bus在电梯中的应用 电梯控制系统简介 CANopen协议简介 CANopen电梯子协议 CANopen电梯虚拟设备和对象字典 CANopen电梯预定义通讯对象-CAN-bus applications in the elevator elevator control systems Introduction Introduction to the CANopen protocol sub-protocol CANopen CANopen Lift Elevator
elevator
- 基于单片机控制的电梯程序.可在电梯运行中控制电梯层数,也可暂停-according to SCM for elevator
elevator
- 电梯控制系统 （1） 电梯有14层，复位后停在地下一层，即0层。 （2） 通过置数功能，可以设定现在所处楼层数。 （3） 设置好想要到的楼层后按下up或down开关，up或down相应指示灯点亮，电梯运行。 （4） 在电梯运行过程中，相应楼层指示灯点亮，数码管显示楼层数，到达目的楼层后，停止指示灯点亮，up或down指示灯熄灭。 （5） 电梯每1秒上升或下降一层。 -elevator control system
The-elevator-PLC-control
- 介绍利用PLC可编程控制器在升降电梯中的应用,包括电梯逻辑时序控制、通信等功能的实现-Describes the use of elevators PLC programmable controller in the application, including the realization of the elevator logic timing control, communications and other functions
CAN-bus-based-elevator-control
- 基于CAN总线的电梯控制,51单片机实现的，可以用来研究CAN总线通信以及电梯控制。-Elevator control based on CAN bus, 51 MCU can be used to study the CAN bus communications and elevator control.
elevator
- fpga电梯控制程序，有很强的参考价值，希望大家能够喜欢。-fpga elevator control procedures, there is a strong reference value, I hope you will enjoy it.
PLC--elevator
- plc 的电梯控制程序，含有组态软件,控制算法。plc 采用三菱fx1n-plc elevator control program, containing configuration software
Elevator
- 基于stm32f103RBT6的电梯控制程序，以链表管理逻辑关系，定时器中断，实现任意楼层停靠-stm32f103RBT6，The elevator control program，linked list
elevator
- 利用C#编写的一个小程序，可以模拟进行电梯的调度，有10层，可以进行电梯调度-Use C# to write a small program that can simulate the elevator scheduling, there are 10 floors, the elevator can be scheduled
Elevator
- 51单片机利用数码管动态扫描模拟电梯程序。-The use of 51 singlechip digital tube dynamic scanning elevator simulation program.
Elevator
- Simple Elevator simulator for few floors
elevator
- 电梯模拟系统，基本实现了电梯的正常运行所需要的各种功能,例如启动、上、下以及楼层的选择和楼层的显示-Elevator simulation system, the basic realization of the normal operation of the various functions needed for the elevator, for example, started on display as well as the choice of floor and floor
Elevator
- 电梯调度程序程序（模拟电梯的运行，使用Java语言绘制界面，具体说明请见压缩包里的电梯调度程序设计方案报告）-Elevator scheduler program (simulated elevator operation, drawing interface using the Java language, see the specific instructions compression elevator design report scheduler bag)
elevator
- 电梯控制程序，可以根据乘客的按键，完成电梯的智能调度，包括顺路筛选，自动屏蔽非法操作等-Elevator control procedures, according to the passenger' s buttons, complete the elevator intelligent scheduling, including Shun screening, automatic shield illegal operation
elevator
- 编写的6层电梯控制程序，包括原文件和仿真文件等，注释详细-Written in six-story elevator control procedures, including the original files and simulation files, detailed notes
Elevator-3
- 三路电梯程序，完成10层楼的传输。左边为电梯内部的按键情况，后面为楼层按键情况。-Three-way lift procedure, completed 10-storey transmission. Inside the left button for the elevator, the floor behind the keys to the situation.
elevator-controller-VHDL
- 电梯控制器程序设计与仿真，本文为DOC文档，附有源码和仿真波形-The elevator controller programming and simulation, this paper for the DOC document, attached to the source code and simulation waveform