搜索资源列表
stm32_gpio_demo
- this project to test GPIO of board chip STM32F10x , it has simple to understand how to progarm , and how to config pins of chip . it s also point to the thing very importan related RCC , the clock for chip
LED
- 1设计要求 PC6,PC7,PD6,PD13 LED快速交替闪烁。 2 硬件电路设计 在开发板上通用I/O口PC6,PC7,PD6,PD13作为控制D1,D2,D3,D4的控制线。 3软件程序设计 根据设计任务要求,软件程序主要包括: (1) 配置GPIO口,将PC6,PC7,PD6,PD13配置为上拉输出模式。 (2) 延时控制相应端口的置位和复位。 4 运行过程 (1) 使用Keil uVision3 通过
adroid-LED
- mini2440Adroid系统下的GPIO口控制测试 -mini2440Adroid system under test mini2440Adroid GPIO port control system of the GPIO port to control the test
GPIOO
- 设置GPIO输出的一个驱动,添加在wince6的驱动文件中,需要编写vs2005的测试工程后可用。-this is a gpio output test driver, you can add this to the coresponding folders. wish it be useful.
TMS320X281xDSP_DEMO
- 本光盘包含的应用程序如下: Test1 C语言编程 Test2 硬件测试 Test3 GPIO应用 Test4 定时器应用 Test5 ADC应用 Test6 SPI接口应用 SPI接口DAC(SPI_DAC5617) SPI_DAC_ADC SPI存储器扩展(SPI_EEPROM) Test7 SCI应用 中断模式(SCI_interrupt) 状态查询模式
linux-IO-control
- 在ARM9开发板的linux2.6.12环境下控制GPIO端口的驱动程序和测试程序,已经测试通过-the driver and test program to control GPIO on ARM9 board in linux2.6.12
Sumador-RS05---Leds-OK
- Gpio leds test. can test 4 leds of board pinout
his_gpio_test
- 关于海思芯片的光栅的GPIO控制车辆进出的拍照测试-Think about the sea of chip of the grating GPIO control cars in taking pictures of the test
msp430test
- msp430f149开发板例程,控制8个LED闪烁,用于测试下载功能是否正常-msp430f149 test code for led gpio
F2812gpio_loopback
- TI公司F2812芯片的GPIO口自测试程序,可用于测试GPIO口是否正常工作-TI s F2812 chip GPIO port can be used to test self-test program, the GPIO port is working properly
GPIOTest
- General Purpose Input Output (通用输入/输出)简称为GPIO,或总线扩展器,利用工业标准I2C、SMBus™ 或SPI™ 接口简化了I/O口的扩展-General Purpose Input Output test
GPIOceshechengxu
- ARM7外围GPIO口测试程序 ,完整实用-ARM7 external GPIO port test program, complete and practical
button-linux
- 嵌入式linux按键驱动程序及相关的测试程序,通过定时器定时扫描GPIO电平的高低以判定按键是否按键,通过延时去抖-Embedded linux key drivers and test procedures, by the level of timer scheduled scans the GPIO to determine whether a key button debounce with delay
LED
- linux的led驱动程序加测试程序。s3c2410的gpio驱动-Linux led driver and test program. the s3c2410 The gpio driver
app
- linux2.4 GPIO at91rm9200 应用层测试程序-linux2.4 GPIO at91rm9200 application test
test_utils.tar
- GPIO LED 测试工具源代码,可以用来检测开发的主板GPIO LED设备是否工作正常-GPIO LED test tool source code, can be used to detect the development of motherboard GPIO LED device is working properly
STM32F103ZET6_CAN
- 1、STM32系统配置(NVIC、RCC、GPIO),CAN功能块配置(循环模式或正常模式) 2、本例程只是完成了CAN的简单测试,并没有实现多机通信,想要了解的朋友可以查阅这方面的资料。-1, STM32 system configuration (NVIC, RCC, GPIO) the CAN function block configuration (circulation mode or normal mode) 2, the routine just completed a
PHYmain1
- 测试接口,FLASH,gpio,SRAM-test interface,flash,gpio,SRAM
gpio_IRQ.tar
- 在DM365下实现的用一个GPIO脚实现中断,中断号,测试代码等内容完整。-DM365 under achieve GPIO pin interrupt, the interrupt number, test code is complete.
SMOKE_test
- CC2540烟雾报警器模块测试程序 烟雾报警器,检测到烟雾时,GPIO输出高电平,报警消失后,变低电平-CC2540 module test procedures smoke alarm smoke alarm, when smoke is detected, GPIO output high, the alarm disappears, goes low