搜索资源列表
KeyIn
- 键盘输入。当检测到有按键输入时,对发光二极管LED4进行取后控制。 使用I/O口输入方式对按键KEY1进行扫描-LPC2119 GPIO CODE
LPC2119-2129ChipDetails
- lpc2129data sheet for learning about arm7
RS_CAN250K
- 一个CAN总线应用的实例 ,采用LPC2119处理器-Examples of applications of a CAN bus, using LPC2119 processor
gfhh23--0
- danpianji lpc2119 yuandaima
Test
- LPC2119/2129/2194/2292/2294 是基于一个支持实时仿真和跟踪的 16/32 位 ARM7TDMI-S CPU 的微控 制器,并带有 128/256k 字节(kB)嵌入的高速 Flash 存储器。128 位宽度的存储器接口和独特的加速结构使 32 位代码能够在最大时钟速率下运行。对代码规模有严格控制的应用可使用 16 位 Thumb 模式将代码规模 降低超过30 ,而性能的损失却很小。 -These are stress ratings only and fun
lpc2119Chinese
- 恩智普半导体LPC2119芯片手册中文资料,不熟悉英文的朋友们可以-NXP Semiconductors LPC2119 chip manual Chinese general information, are not familiar with English friends can see ... ...
ARM2119s101205
- LPC2119 2路485通讯程序, 使用查询通讯, 时间中断, 查询方式-RS485 COMMUCATION , TIME INTERUPER
Adc
- lpc2119的ADC程序,上位机软件实现数据的显示 -lpc2119 of the ADC program, the PC software for data display
spi_test
- LPC2119 SPI例程,适用于英蓓特的开发板-LPC2119, SPI routines that apply to the development board of Embest
soft
- 基于ARM的CAN总线照明控制系统设计,主要采用了主从CAN节点进行网络通信,对照明等设备的定时开关控制。实验中,采用1个主节点,2个从节点进行实验。主节点采用LPC2119处理器和2.8寸TFT,从节点采用STC89C52作为处理器,SJA1000CAN从控制器-The design of intelligent lighting control system based on CAN bus
LPC2119adc
- lpc2119 的AD实验包括源代码 仿真 -the lpc2119' s AD experiments include simulation
CAN
- LPC2119的CAN发送接收程序,ic18fxxxx CAN总线发送接收子程序-The LPC2119 CAN transmit and receive program, ic18fxxxx CAN bus sending and receiving subroutine
DS18B20_LPC2119_Program
- 本程序是ARM LPC2119与DS18B20通讯接口配置程序,并早已成功通过实际项目验证测试,请大家放心应用。-The program is the ARM LPC2119 DS18B20 communication interface configuration program, and has already successfully passed the validation test of the actual project, please rest assured that app
lpc2119_ucosii
- 基于lpc2119开发板,keil环境的ucosii系统开发-Based on lpc2119 development board, keil the environment ucosii system development
source
- 包含LPC2119开发板的全部实验的所要用的程序,比如基本的CAN通信试验,AD实验等等,经验证,没有错误 -The program contains all the experimental use LPC2119 development board, such as basic CAN communication test, AD experiments, etc., proven, no errors
基于ARM的CAN总线照明控制系统设计
- 基于ARM的CAN总线照明控制系统设计,主要采用了主从CAN节点进行网络通信,对照明等设备的定时开关控制。实验中,采用1个主节点,2个从节点进行实验。主节点采用LPC2119处理器和2.8寸TFT,从节点采用STC89C52作为处理器,SJA1000CAN从控制器.(Based on ARM CAN bus lighting control system design, mainly uses the master-slave CAN node for network communication