搜索资源列表
LCD5110_mega8
- LCD5110 mega8 -LCD5110 mega8 ..............
pwmfangzhenchengxu
- 本设计采用基于AVR内核的MEGA8单片机，该单片机集成了相当丰富的片上资源，其中就包含有三路独立的PWM输出，在8MHz的晶振频率下，最高可以输出31.25KHz的8位分辨率脉宽，设计中主要是利用MEGA8的PWM输出功能来完成三路PWM波形的输出，其中两路是同步反向输出，频率、脉宽均可调，另外一路单独输出，脉宽可调。-This design based on AVR core MEGA8 microcontroller, which integrates a rich on-chip res
USB_SD_mega8
- SD读卡器原理图，采用mega8单片机，对于开发USB接口非常有帮助。-Schematic of SD card reader,based on mega8 MCU,it s very help for development of USB interface.
AVRJATG
- AVR JATG 下载线的完完整资料，包括原理图，PCB图等-End of the line AVR JATG to download complete information, including schematics, PCB maps, etc.
xiaocui_Pinwheel
- atmel Mega8 和74hc595串行IC写的风火轮程序.以及硬件电路和安装向导.此程序并非我单独开发..在此感谢程序员小崔的大力支持.-atmel Mega8 and 74hc595 Hot Wheels programs written in the serial IC. as well as hardware circuits and the installation wizard. This program is not me alone .. like to thank the
led
- mega8初学实用代码欢迎共享 用于学习avr单片机的好帮手！-welcome share whit you! mega8
MEGA8DS18B20
- mega8读取温度芯片DS18B20并通过LM016显示，可准确的显示正负温度. 程序以驱动形式写出，只需修改端口即可 附有Proteus仿真模型-mega8 read the temperature through the LM016 chip DS18B20 show positive and negative temperature can be accurately displayed. procedures to drive the form of writing, you c
164hc165io
- 74hc165多片级联，并通过MEGA8以IO口模拟SPI方式读取，发送至74HC164多片级联的LED灯显示 程序以驱动形式写出，只需修改端口即可，附有Proteus仿真模型-74hc165 multi-chip cascade through MEGA8 to simulate SPI mode IO port to read, send to 74HC164 cascaded multi-chip LED lights display the form of written proce
avr_usb_isp_source_code
- 用mega8做的USB ISP 下载线，这里用软件+IO的方式实现USB通信，很有价值-Mega8 do with USB ISP download cable, where software+ IO means to achieve the USB communication, great value
uart
- 一个mega8的串口发送接收程序，对于初学者来说是很有用的哦-A serial send and receive procedures mega8，it good for beginner。
ADC
- 一个关于mega8的AD转换和串口发送接收程序，转换结果用数码管显示-One of the AD converter and serial mega8 receiving program to send the conversion result with digital display···
lcddisplay
- mega8单片机驱动1602液晶的汇编程序，AVR Studio调试通过-mega8 Microprocessor 1602 LCD assembler, AVR Studio debugger by
iccavr
- uc/os系统在mega8上移植,编译后大概为50 的程序量-uc/os on the system mega8 transplantation, compiled about the amount of 50 of the programs
f_count
- 基于mega8的频率计程序.四位数码管显示.-The frequency counter program based mega8. 4 digital display.
count
- 基于mega8的中断计数器.四位数码管显示.-Based mega8 interruption counter. 4 digital display.
AD_Com_OK
- AVR单片机Mega8 AD采集+串口发送，采用ICC-avr开发。-AVR microcontroller Mega8 AD Acquisition+ serial port, developed by ICC-avr.
ICC_atmega16
- 验源码。 MEGA8芯片编程的注意事项： 1）、如果晶振被编程为外部时钟，此时只有使用外部有源晶振才可重新对MEGA8进行编程。 2）、如果用户只有串行编程设备，请不要将RESET功能禁止，否则只有使用并行高压编-Test source. MEGA8 chip programming note: 1), if the crystal has been programmed for external clock, this time only using the external crystal
RC232
- 此程序完成和mega8的串口通信,并且完成对防盗系统的检测和信息处理-communicate with mega8 using Aysnc Serial
C51ToAvrfuseDef
- C51一键恢复AVR熔丝位，包含MEGA8和TINY2313的代码，带大量注释。可以更改熔丝默认值来支持其他芯片，可以通过串口监视软件来查看恢复前后的熔丝位。支持rest脚被锁问题，带用proteus格式的仿真电路和PCB制版。-C51 a key recovery AVR fuse bits, including MEGA8 and TINY2313 code, with a lot of comments. You can change the default value fuse to s
18B20
- 本程序为采用mega8 和18b20的温度采集程序-18B20