搜索资源列表
spi_verilog_master_slave_latest.tar
- 该项目从需要具有强大而简单的以VHDL编写的SPI接口核心开始，用于通用的FPGA到设备接口。 所产生的内核产生小而高效的电路，从非常慢的SPI时钟到超过50MHz的SPI时钟。-This project started the need to have robust yet simple SPI interface cores written in VHDL to use in generic FPGA-to-device interfacing. The resulting co
STM32-GD25Q32B
- STM32下使用SPI接口驱动GD25Q32flash的代码，代码采用模块化编程，清晰明了。-STM32 using the SPI interface to drive GD25Q32flash code, the code using modular programming, clear.
SPI-slave-system
- FPGA时序逻辑设计：串行外围设备接口SPI从设备系统，包括串行时钟线SCK，主机输入/从机输出MISO，主机输出/从机输入MOSI和低电平有效的从机选择线SS。环境为Quartus。-FPGA Timing Logic Design: Serial Peripheral Interface SPI Slave Device System Includes Serial Clock Line SCK, Host Input/Slave Output MISO, Host Output/Slave
spi_slave
- FPGA实现SPI接口的从机功能，接收和发送全双工运行，接收到的数据以八位LED灯显示-FPGA to achieve the SPI interface the machine function, receive and send full-duplex operation, the received data to eight LED lights
w5500_spi_fpga
- 共两个文件，一个是对网络芯片W5500进行控制的master spi接口，另一个是w5500命令控制逻辑，命令格式按照w5500芯片的要求，分为地址段，控制段和数据段进行统一控制。此外提供w5500芯片初始化及读写控制流程图。-A total of two documents, one is the master SPI interface for network control chip W5500, the other is a w5500 command control logic, co
apb_spi
- Simple SPI interface realization on Verilog HDL with parameterized FIFO and APB interface
ENC28J60_Interrupt
- 基于DSP的SPI接口应用之网络控制器ENC28J60，附例程代码-Network controller ENC28J60 SPI interface based on DSP application, subroutine code
MCU(modbus)
- 用modbus协议和SPI接口实现微波模块的频率和幅度控制功能-Use modbus protocol and SPI interface to implement the frequency and amplitude control of the microwave module
NXP-SC16IS752-DEMO
- 此代码是基于NXP公司的串口扩展芯片SC16IS752的驱动程序。此芯片可以用IIC或者SPI接口进行控制，两种程序都有，并且是基于C51的代码。简单易懂，方便进行移植。-This code is based on NXP s serial port expansion chip SC16IS752 driver. This chip can be used IIC or SPI interface control, both programs have, and is based on the
SPI_FLASH.X.X
- MAPLAB工程文件，可实现SPI接口与FLASH的读写控制，基本功能已经配置好，可自行添加其他逻辑。-MAPLAB project file, can achieve SPI interface and FLASH read and write control, the basic function has been configured, you can add other logic.
Prj_MCP41010_STM32F030F4P6
- Initializing and make an SPI interface to work with the digital potentiometer (MCP41010) with STM32F030F4P6 is performed in Keil-MDK v5 with STM32Cube.
Prj_MCP41010_STM32F030F4P6
- Initializing and make an SPI interface to work with the digital potentiometer (MCP41010) with STM32F030F4P6 is performed in Keil-MDK v5 with STM32Cube.
Demo
- Adafruit_GFX和Adafruit_SSD1306这两个文件夹是库文件，请将其放入"libraries"文件夹内； Demo.ino为演示程序，正确接线并下载到Arduino板子上即可。 0.96寸SPI接口arduino接线方式： OLED屏 arduino开发板 GND GND VCC 3.3V 或5V SCL 10 SDA 9 RES 13 DC 11 CS 12 七针模块有cs脚；直接连接就好了；如果是用六针的CS默认已
MCP2515
- 在树莓派3上用PYTHON语言实现CAN总线的发送与接收，使用MCP2515模块，与树莓派的接口位SPI接口。(In raspberry Pie 3, the CAN bus is sent and received in PYTHON language. The MCP2515 module and the interface bit SPI interface of raspberry pie are used.)
ADF4002
- ADF4002源码，c语言编写 ，spi接口，输出稳定的正弦波(ADF4002 source code, c language, spi interface, the output stable sine wave)
ExampleCode_iSensor_ADIS16405
- ADIS16405 传感器的寄存器读写，spi接口，单片机例程(ADIS16405 sensor register read and write, SPI interface, SCM routine)
5.OLED延伸——界面（显示MPU6050数据）
- STM32驱动显示六角OLED，SPI法，附带一个已经编辑完成的界面（带4个按键）(The STM32 driver displays six corners, OLED, with SPI, with an edited interface (with 4 buttons))
okja-english-1133611
- spi lcd interface cpde
sdtest
- 这个是一个verilog程序，可以用spi读取sd卡中的内容，存到fifo中(This project can read the data from SD card through SPI interface and store the data in FIFO.)
3b669a6c35f6549643d57031dadf3518
- Keil C写的ADI的24位ADAD7799使用SPI接口程序(The ADAD7799 24 bit ADI written by Keil C uses the SPI interface program)