搜索资源列表
7.ov7670摸索
- stm32输出color到USART 1,串口调试助手可查看某一点的RGB565值(STM32 output color to USART 1, serial debugging assistant, you can check the RGB565 value of a point)
EXTI+USART
- 外部中断使用,源地工作室stm32最小系统外部终端使用(exitThe use of external interrupt source, studio STM32 minimum system external terminal use)
stm学习中程序
- 其中包含了一个以gpio简单设置的程序以及usart通信和pwm设置的程序(It contains a program that is simple to set up with GPIO, as well as programs for USART communications and PWM settings)
DREAMER STM32开发板实验7 - 串口通信
- 通信试验,端口设置,可利用作为基本工程伸延开发(Communication test, port setting)
串口通讯
- 实现STM32串口通讯,以及OLED显示。(STM32 serial communication, and OLED display. Platform for keil DMK, engineering can be compiled to run.)
21ic下载_基于STM32的CAN总线收发程序
- 实现can通信,经本人验证完全可以使用,拿去吧。(#include "can.h" #include "led.h" #include "delay.h" #include "usart.h" #include "led.h" #include "delay.h" #include "key.h" #include "sys.h&qu
第六个工程-dma-usart
- 在mdk环境下利用stm32 f407单片机实现串口dma功能(To achieve the MDK5 stm32f407 single-chip serial port dma function)
83813466STM32-USART
- 单片机实现串口通信 中断实现数据的接收(MCU serial communication interrupt to achieve data reception)
printf(polling)
- 要让STM32能够顺利发出数据,要进行如下配置 PA9,PA10管脚要配置, USART也需要配置波特率,数据有几位,停止位,数据流等(stm32 uart communication)
Sim_USART
- 在STM32平台 模拟USART通讯(1bit起始位,1bit终止位,8bit数据,无奇偶校验)(Simulation of USART communication on STM32 platform)
BSP
- stm32吧can转接成usart can里面包含初始换 速率500kb/s usart 19200(The stm32 bar can be converted to usart which can contain the usart 19200 with an initial conversion rate of 500kb / s)
usart 升级
- stm32通过串口来升级,从uboot启动,如果不需要升级代码,则直接跳转到应用代码,如果要升级则等待串口通过secureCRT YMODE协议发送来得数据,注意(程序中由于ymodem协议没有发送文件大小,程序中是随便写了一个文件大小,对于我的app足够用),在app中随意按下按键,通过可以从应用程序跳转到uboot,然后发送1,通过ymodem协议发送.bin文件后,按下3则跳转应用程序(STM32 through the serial port to upgrade, starting
20171208_USART
- use stm32 to cal volt ,and use usart send the data to pc
mySystemTest1
- 基于FreeRTOS的麦轮四轮底盘系统模型,CAN和USART通讯(this is a system base on FreeRTOS, and you can build your robotics system on this especially on this code. Communiciate by USART and CAN!)
STM32USART
- 使用HAL库开发stm32串口通讯例子。注意端口硬件配置不同。(Use the HAL library to develop an example of the STM32 serial communication. Notice that the port hardware configuration is different.)
ADC_temp_sensor
- Internal temperature sensor development with USART to USB conversation for ARM CORTEX M3 core MC stm32f100.
PM-F103-16MHZ
- 基于STM32F103C8T6芯片,串口解析数据,OLED显示程序(Serial port parsing data, OLED display program)
MyBluetooth
- 基于STM32 蓝牙模块 手机通讯 Android studio APP 上位机程序(Android studio APP host computer program based on STM32 Bluetooth module)
USART1
- 测试stm32F405的串口程序,晶振是25MHZ(test stm32F405 usart)
IAP-Bootloader V1.0
- IAP(In Application Programming)即在应用编程,IAP是用户自己的程序在运行过程中对User Flash的部分区域进行烧写,目的是为了在产品发布后可以方便地通过预留的通信口对产品中的固件程序进行更新升级。 通常实现IAP功能时,即用户程序运行中作自身的更新操作,需要在设计固件程序时编写两个项目代码,第一个项目程序不执行正常的功能操作,而只是通过某种通信方式(如USB、USART)接收程序或数据,执行对第二部分代码的更新;第二个项目代码才是真正的功能代码。(IAP (I