搜索资源列表
STM32-uCOS-II
- st的M3的OS移植，包括了GPS定位程序MMC卡驱动
uCOS
- UCOS工程,采用keil开发工具开发,程序中基于stm32v100处理器. 在uC/OS-II中建立3个任务Taskled、Tasktep、Taskadc和三个中断。 Taskled初始化时，LED 依次点亮，当按下 Key 键时产生中断。 中断服务子程序内容：灯全部熄灭，2 秒钟后发光二极管全部点亮，再过 1 秒钟后中断返回。 Tasktep用来实时检测温度传感器u4的温度。STM32通过IIC接口获取温度传感器的温度。 Task
Comparative_Control_Program
- STM32 STM32F103RCT6 UCOS II操作系统工程模版-STM32F103RCT6 UCOS II STM32 operating system engineering template
stm32-zigbee-ucos-ucgui
- 优化驱动STM32奋斗版ucOS II V2.86 uCGUI 3.9 DEMO： 此例程基于ucos ucgui 演示了ucgui自带的图形例程。-UcOS II V2.86 uCGUI STM32 3.9 DEMO: this routine based on the ucgui UCOS demo ucGUI own graphics routines (board DEMO is this routine).
STM32---uCOS-II
- 移植好的基于STM32的uCOS源码,可以直接添加自己的任务-Based on the STM32 good transplant uCOS source, you can add your own tasks directly
STM32
- 用Keil开发的STM32基于UCOS-II的消息队列接收发送数据的程序，适合参考学习借鉴。-Using Keil STM32 development based UCOS-II message queue to receive the transmission of a program, for reference learn from.
STM32
- 用Keil4编写的STM32的基于uCOS-II的操作系统的邮箱程序，可用邮箱发送接收数据，亲测可用-With Keil4 prepared STM32-based operating system uCOS-II-mail program that you can send and receive E-mail data, pro-test available
ucos_ii-config-on-stm32
- ucos ii 的配置与移植，stm32配置，IAR开发环境，调试OK，亲测可用相应项目中-ucos ii configuration and transplantation, stm32 configuration, IAR development environment, debugging OK
uCModbus(STM32)
- STM32F103VET6 uCMODBUS 五串口通讯 ucos ii modbus主机从机-STM32F103VET6 uCMODBUS ucos ii modbus
Micrium-uCOS-II-V286
- ucosii2.86源码，单片机嵌入式参考-ucosii2.86 STM32
stm32-UCOSIII-huchi
- 使用STM32使用UCOSIII互斥信号量! -Use the STM32 to use the UCOS II mutex!
stm32-UCOSIII-message
- 使用STM32使用UCOSIII的消息传递机制!-Use STM32 to use the UCOS II messaging mechanism!
uCOS-II-2.92P-GUI(VET6)
- 基于STM32+UCOS+GUI的MODUBS主从机，本人已删除应用层代码，但总体框架是稳定拿来就可用的。-STM32+UCOS+GUI based MODUBS master and slave machine, I have deleted the application layer code, but the overall framework is stable on the available.
LED+UCOS_2.90
- 基于STM32的ucosii代码，能实现在cotex-M3内核芯片上直接使用，属于keil软件(STM32 based on the uCOSII code, can be achieved directly in the cotex-M3 kernel chip, belonging to keil software)
stm32_pwm
- PWM输出脉冲，使用 pwm函数(TIMx, Freq)，即可傻瓜式完成PWM频率输出。(PWM with STM32, by using a simple function)
WiFi_Slave_uCOS_II_WriteCard
- STM32平台上基于ucos-II移植了RFID和WiFi的驱动程序，可以读取M1射频卡，并通过WiFi模块（ESP-01）发送到局域网内其他主机(STM32 platform, based on the ucos-II transplant RFID and WiFi driver, you can read the M1 radio frequency card, and through the WiFi module (ESP-01) sent to other hosts within
my_ucos_Template
- UCOS II 在stm32F103的稳定移植，可以直接使用在项目中，例子中建立了两个任务，IO口切换(The stable porting of UCOS II in stm32F103 can be used directly in the project. In the example, two tasks are set up, IO port switching)
stm32_ucosII_移植demo
- ucos-ii在stm32上的移植demo(ucos-ii stm32 transport code demo)
Micrium_STM32L476G-EVAL_OS2
- UCOSII，基于STM32L47x平台的移植方案，目前为IAR平台。(UCOSII, STM32L47x platform based on the transplant program, the current IAR platform.)
program for my
- 内含九个独立工程，主控芯片 STM32F108C8T6。九个工程分别为：操作LED灯；操作485；操作ADS1015 12位ADC芯片；操作济南有人的网口；两个版本的PID控温程序；外部时间程序；操作ch376读写SD卡程序；ucos-II+mudbus测试程序。(Contains nine independent works, master control chip STM32F108C8T6.The nine projects are: operating LED lamps;Operati