搜索资源列表
s3c2410,iar
- s3c2410 ads下的测试程序移植到 iar ewarm v5.2;包括 Please select function : 0 : Please input 1-14 to select test 1 : Real time clock display 2 : 4 key array test 3 : Buzzer test 4 : ADC test 5 : IIC EEPROM test 6 : Touchpanel test 7 : 3.5# TFT LCD 240*320 test 8
R8C2B-UART2
- 该片子的UART0 和UART1的串口均能正确中断收发.-UART0 and UART1 of the film' s serial port can send and receive the correct interrupt.
ts_10key
- 使用ST单片机STM8S105源程序代码,包含大多数基本功能。-STmicrocontroller family- STM8S105
Uart2
- 串口通信程序,包括读取中断、解读和发送程序,代码已经通过测试!-Serial communication program, including reading the interrupt, read and send the program, the code has been tested!
Timer32BitRTC
- 基于《Stellaris外设驱动库》的例程:定时器32位RTC用法示例(32.768kHz振荡信号从CCP2管脚输入,RTC时钟从UART2输出) 本实验程序演示了如何使用定时器配置为32为RTC模式,并使用RTC定时器产生匹配中断。每次进入中断函数中由串口发送显示一次当前时间,初始时间假设为9:58:40。 本实验需要一个32.768kHz的RTC时钟源,本范例把TIMER0A配置成了16位PWM模式,利用CCP0脚输出频率大致为32768Hz的PWM波,免去了用户外接32
UART2
- vhdl code for implementation of an UART
UART2
- msp430的串口通信程序 学习msp编程的好材料-msp430 serial communication program
uart2test
- 基于CS6209MCU的UART2的驱动测试原代码,用KEIL C51编写-UART2 on the CS6209MCU test driver source code, prepared with KEIL C51
UART2
- SmartARM2200基础实验扩展实验UART实验2-SmartARM2200 basic experiments Experiment 2 extended Experiment UART
uart2
- 这是一个用vhdl 编写的UART控制程序,已经通过测试-UART
LPC2368KitV0.2
- lpc2368下移植ucosii,实现uart0,uart1,uart2各个接口通信。缓冲区采用队列实现接收发送。-lpc2368 transplanted under ucosii, to achieve uart0, uart1, uart2 each interface communication. Achieved using a queue to receive a buffer to send.
uart2
- c8051f320的接无线模块的发射程序(已经调试好的)-void WU_Send() { unsigned char i=0 WU_OK =1 for(i=0 i<6 i++) { while(!WU_OK) SBUF0 =send[i] WU_OK =0 } }
uart2
- a small uart implementation with Verilog
UART2
- 此文件是在LPC2368开发板上开发的,UART驱动以及中断实现-This file is in the LPC2368 development board development, UART drivers and interrupt
lm3s1138_adc
- 基于《Stellaris外设驱动库》的例程:处理器直接触发ADC采样 本实验演示配置ADC采样序列0,通过处理器直接触发ADC采样,ADC模拟量需从外部输入(ADC0),最大不能超过3.0V,因为ADC内置的参考电压为3.0V。 在进行ADC配置之前,必须首先进行PLL锁相环配置(详见EasyARM1138例程\02 SysCtl(系统控制)\3 锁相环PLL设置)。错误配置PLL将使系统进入异常。 ADC采样得到的数字量将利用超级终端从串口读出 。本开发板采用US
UART2
- Code about UART for ARM7
UART2
- 串口UART描述,一经通过仿真并硬件实现。-Serial UART descr iption, once the simulation and hardware implementation.
uart2
- 改进的串口通信,通过程序大家看到要实现的功能-chuankou
M16C_I2C_Simple_Master_API
- This I2C Master API for Renesas microcontrollers uses UART2 mode for M16C family and SSU for R8C family.
uart2
- uart routine for transmitting characters a to z . -uart routine for transmitting characters a to z .