搜索资源列表
I2cAnalyzerDll
- 如果正在学习USB相关的可以参考,上位机提供了动态库及源码,如果写应用界面可直接调用动态库即可,无须对底层做过多了解,但这些也只属于一个初始框架,希望哪位有VC++经验而且有兴趣的,可以细化并提供出一个更好的供广大爱好者使用 -If you are USB-related learning can refer to the host computer provides a dynamic library and source code, if written application inte
7.22Apptest_wr
- c68013 ,USB,VC 上位机程序,可实现读写并测试读写速度-c68013,USB,VC program,read and write
computer00
- 电脑圈圈写的USB驱动测试上位机软件,完整工程-Computer00 s USB drive test PC software
ADC_ADC1_DMA
- stm32F103zet平台,使用DMA采集数据,并通过USB口上传上位机-stm32 platform, collecting data using DMA
HIDTest
- USB HID上位机程序,可以实现对指定HID设备的识别和数据收发。-USB HID host computer program, you can achieve the specified HID device identification and data transceiver.
MyUSB_HID_KEIL
- STM32 USB与上位机通信例程.描述有下位机USB的配置等,发送和接收数据函数的说明
cSharphid
- C# HID 关于HID协议通讯主要是上位机的代码,与USB的通讯-C# HID HID protocol communication is mainly on the host computer code, and USB communication
SLAVE-FIFO8test
- 用于FPGA板子上的USB调试,包括上位机、驱动程序、下位机程序、应用程序。-Used for USB debugging, including PC, and PC driver program and application.
SLAVE-FIFO16-test
- 基于FPGA的USB调试代码,包括上位机代码、驱动程序、应用程序、下位机代码。-USB debugging code based on FPGA, including PC code, driver and PC, application code.
USB_FPGA_IOtest
- 基于FPGA的USB调试代码,包括上位机代码、驱动程序、应用程序、下位机代码。-USB debugging code based on FPGA,including PC code, driver and PC, application code.
USBButton-control-input-test
- 基于FPGA的USB调试代码,包括上位机代码、驱动程序、下位机代码。-USB debugging code based on FPGA,including PC code, driver, application code.
USBLight-LED-test
- 基于FPGA的USB调试LED灯的代码,包括上位机代码、下位机代码。-USB debugging leds code based on FPGA, including PC and PC code code.
pl2303
- USB单版机通信,可以实现单片机与上位机的通信。可以实现2303USB芯片的处理。-USB commnuication example source code.
14program_pcb
- 1.C8051F320做的测试USB速度可到240KBps. 包含单片机源码,驱动和上位机程序2.MCUc8051f040用自带的IIC控制器读写实时钟芯片PCF8563,完成BCD码到十进制码转换3.PCF8563的驱动程序,通过模拟IIC总线对PCF8563进行访问,有完整的读写报警,定时中断,最后把时间显示在LED上4.USB CDC using C8051F320340, virtual COM port thru usb connection5.本库函数实现了C8051F020 SMB
USBXPRESS
- USB通信的上位机软件,采用USBXPRE-USB PC communications software, using USBXPRESS
full_motioncontrol
- 绘图输出控制软件,主要适用于激光切割、雕刻等,步进电机控制绘图输出的设备。支持并口控制和USB下载控制。 资料包含: 上位机源代码:控制设备输出的源代码; 下位机源代码:芯片(ARM、DSP等)控制源代码; 接口源代码:可重编程的源代码,供完善程序; 端口控制源代码:LPT并口控制和USB端口下载源代码; 程序文件:控制软件的可执程序和程序演示视频。 程序可用于电机控制测试和应用于根据图形输出的控制软件,源程序可任意修改和应用于商业用途。 希望为电
MyUsbHid
- 《圈圈教你玩USB》之 用户自定义的USB HID设备 ******\r\n", "****** AT89S52 CPU ******\r\n", "****** 建立日期:",__DATE__," ******\r\n", "****** 建立时间:",__TIME__," ******\r\n", "****** 作者:电脑圈圈 ******\r\n", "****** 欢迎访问作者的 ******\r\n", "****** USB专区:http://gro
MyUsbDevice
- 《圈圈教你玩USB》之 用户自定义的USB设备 AT89S52 CPU 打开上位机应用软件,然后按K1-K8分别进行测试 -" Circle teach you to play USB" in the user-defined USB device AT89S52 CPU open PC application software, and then press the K1-K8 were tested
USB_Control_MCU
- 基于C8051F320的USB通信,接收上位机设置的参数DA转换送给外部引脚,AD转换采集外部模拟信号-Based on C8051F320 USB communication, PC to receive the parameters set to give an external pin DA converter, AD converter acquisition of external analog signals
ourdev_548466
- 全球最大的中文技术讨论区,请访问CSDN论上位机测试-USE FOR USB TEST