搜索资源列表
sht1
- I2c c语言串口通信协议VisualC++-TurboC-I2c VisualC++-TurboC VisualC++-TurboC
80C51_1
- 1.异步通信软件模拟2.基于RS-232的串口通信3.基于RS-485的多机通信4. I2C总线协议的软件实现5. SPI总线在单片机系统中的实现6.-wire-1. Asynchronous communication software simulation 2. Based on the RS-232 serial communication 3. Based on the RS-485 Multi-machine communication 4. I2C bus protocol soft
MODBUS
- MODBUS串口通信编程驱动,采用MODBUS通信协议,和某智能仪表进行串口通讯,采集解析数据,本软件已经在工程中应用,绝对实用,对学习MODBUS串口编程有比较大的帮助!经过实际应用,绝对真实!-MODBUS serial communication programming-driven, using MODBUS communication protocol, and an intelligent instrument for serial communications, data coll
shizhong
- 如果是用pc的串口传输数据就好办了,可以安装一个串口监视工具(如AccessPort)。电脑串口一般是2、3、5三根线通讯,2是txd,3是rxd,5是GND,但是电脑的逻辑电平与单片机的逻辑电平不同,具体看串口通信协议,网上很容易搜到。 IIC总线上的数据可以通过示波器查看,两个探头,一个连接clk,另一个连接sda,IIC通信时可以观察到传输的数据。 -If you are using pc' s serial port to transfer data much easier t
com
- vC++做上位机实现串口通讯,符合RS485通信协议-vC++ do PC Serial communication line RS485 communication protocol
vbcom
- VB串口收、发程序 包括通信协议 帧格式组织等-VB serial sending and receiving procedures, including communication protocol frame format organization
Serialcommunication
- 编写的串口通信协议,通过这个程序可以实现两台电脑之间的通信-serial cummunication
ictaommgr
- 一个不错的linux小应用,可以管理多个串口设备,一个简单的,自编的串口通信协议。-simple linux serial port communication to manager multi serial device.
13-45
- 本程序能够完成的功能是,自动或手动测温,读取配置寄存器,温度下限寄存器,温度上限寄存器,设定温度上限及下限,当温度到达预定的温度的时候报警。所有的读取操作都可以在数码管上显示。其中,温度的上限通过计算机用串口通信协议传输给FPGA内部寄存器然后按动开关写入。同时,本程序还驱动了一个直流电机,温度高的时候电机转速高,温度低的时候转速降低直至停转。数码管可以实时显示电机转速,2秒刷新一次。数码管的显示可以在显示的温度、寄存器值和直流电机转速间切换,切换通过串口进行,计算机发00H时切换到温度及寄存器
138-UART
- 介绍TI 138芯片的串口通信协议及寄存器配置-Introduction TI 138 chip serial communication protocol and the configuration register
USART_AT93C46
- PIC16F877实现串口通信协议数据包通信,同时能通过窗口上位机对AT9346进行读写功能。-PIC16F877 Serial communication protocol packet communication, while the host computer through the window to read and write capabilities of the AT9346.
Xmodem
- 串口通信协议源码,128B/1K协议源码-XMODEM UART PRO
51danpianji_chuankou_tongxin_xieyi
- 51单片机的串行通信协议的实现 串口通信协议-51 single-chip serial communication protocol implementation
UART
- UART串口通信协议的verilog代码-Verilog code of UART serial communication protocol
43563452321
- 以微软公司MSCom串口通信控件为底层接口,建立了一个简单的串口通信协议(spcp)。spcp协议的设计基于帧传输的思想,采用发送/应答/重连/失败的方式进行.利用该协议能实现双机短信聊天、文件传输等实时数据通信功能。-To the Microsoft MSCom serial communication control for the underlying interface, a simple serial communication protocols (spcp). spcp proto
s24_uart
- 这是一个串口通信协议,有详细的说明,欢迎下载!-This a code of uart in verilog ,describled in detail,welcome to download!
1
- 利用C语言编写的51单片机的串口通信协议实现-51 single-chip serial communication protocol using C language
UART51
- 51单片机串口通信协议制定,可以自己定义串口通信协议,用于组建控制网络-51 single-chip serial communication protocol to develop, can define your own serial communication protocol for the formation of the control network
MSComm
- 关于RS232的串口通信协议,用于通讯!-this is a program for communicating!