搜索资源列表
shengyadianlu
- 自己整理的几个升压电路！我觉得比较实用！-Their order of several boost circuit! I think the more practical!
design-of-the-digital-implement-
- tlc494摘要:设计的开关稳压电源，其系统硬件由三个环节组成，即整流滤波环节、直流-直流升压变换（DC-DC）环节、以及测控与键盘显示环节。整流滤波采用二极管桥式整流后加电容滤波电路；由脉宽调制芯片TL494为控制器构成BOOST原理的升压型DC-DC变换器；测控环节由内带A/D转换器的紧缩型单片机STC12C5412AD和简易键显电路及串行D/A转换器构成。软件配合A/D、D/A实现了电压电流的测量和输出电压的步进调-very good it is very important to eve
Flyback_UC3842
- 基于MULTISIM和uc3842的反激式升压开关电源的仿真-MULTISIM and uc3842 based flyback step-up switching power supply simulation
GMcounter
- GM计数管电路，集成升压电路，采样电路，波型处理-GM counter circuit, the integrated boost circuit, sampling circuit, waveform processing
APFC
- 单相Boost升压结构的有源功率因数校正电路仿真设计实例-The structure of single-phase Boost Boost Active Power Factor Correction Circuit Simulation Design Example
1871
- 只电流模式升压芯片,需要极少外部元件的宽输入，电流模式、升压、反激和SEPIC控制器-Only current-mode boost chip requires minimal external components of wide input, current mode, boost, flyback and SEPIC Controller
downup
- 直流降压升压变换器 用于对输入电压的升高或者降低 -DC buck-boost converter is used to raise or lower the input voltage
up
- 升压变换器 用于将输入的直流电压升高至输出 -Boost converter is used to input pressure to output DC
M8_2400
- ATMEGA8_ LTC2400 6位半表头程序 LTC2400最高测量电压为5.3V，超过5.3V或反接都会烧掉。 模拟部分供电最好经过7815稳压，最高输入电压不宜超过18V。 模拟电路与数字电路分开供电。 不要使用开关电源或PWM升压、降压电路供电 -ATMEGA8_ LTC2400 6 ½ -digit meter program LTC2400 highest measured voltage is 5.3V, 5.3V or rev
1xy7z.ZIP
- 燃料电池用大升压比DC_DC器双闭环控制Fuel cell with large step-up ratio DC_DC for double closed-loop control-Fuel cell with large step-up ratio DC_DC for double closed-loop control
S229_Boost_01
- 电力电子DC-DC变换---Boost升压斩波器MATLAB仿真-Power electronics, DC-DC straight converter- Boost chopper MATLAB/Simulink simulation files
boost
- boost升压电路 matlab 调试成功 输出曲线很不错-boost matlab prefect
zui da sheng ya
- Z源逆变器最大升压控制仿真模块，实现Z源逆变器的最大升压控制。-MAx boost control
pvsystem_grid220
- 光伏逆变器的仿真模型 包括升压电路和单相全桥逆变电路-PV inverter simulation model of the boost circuit and the single-phase full-bridge inverter circuit
Boost_12_80V_30W
- 升压变流器 及其控制策略- Boost_12_80V_30W.
shuangshuchu
- 升压双输出直流变换器！就是一个直流电源，经过一个反激升压，输出两个相等电压.-A BOOST DUAL OUTPUT DC/DC CONVERTER
spd3_v01308220805_13
- 该程序基于keil c 环境开发，主要通过pwm产生高压对电涌保护器模块进行监测，将测量的数据通过AD转换变成数字量并进行显示，该程序可以控制多路选择对模块各引脚进行分别升压-The program is based on the development of keil c environment, mainly by pwm high-voltage surge protection module for monitoring, the measured data through the AD
PCBcaijiwaibukaiguanliang121
- 采集外部开关量信号带升压电路，可参考。SCH文件，PCB文件-Collected external switch signal with a step-up circuit, can be found. SCH files, PCB files
PWM-motor-control_
- 这是一个Matlab实现的PWM型直流变换器的Simulink仿真，变换方式是Buck-Boost变换方式。示例，提供了一个从5伏到25伏电压，的升压变换。-This is a Matlab Simulink simulation of PWM DC-DC converter, and transform the way Buck-Boost transform. Example, from 5 volts to 25 volts, the boost transformation.
pull_push_converter_up
- 推挽电路 升压电路，用于车载逆变器，能将电压从12V正激到350V-The push-pull circuit step-up circuit for in-vehicle inverter, can forward voltage from 12V to 350V