搜索资源列表
s3c2410-button
- 开发一个基于中断机制的字符设备驱动程序,为RealARM上的四个按键设置计数值,利用按键产生中断,累加计数值(代表采集的信号数目),在测试程序中读取计数值,达到检测信号数目的目的。 编写驱动程序,为外部中断的四个按键设置计数值,当按键按 下时产生中断,与之对应的计数值递增;
linuxdriver
- 介绍了嵌入式Linux的特点,设备驱动程序的概念,简述了基于uClinux下设备驱动程序的开发方法及过程,最后简述了字符设备驱动程序的开发的实例。
linuxmtd
- Linux MTD介绍: MTD(memory technology device内存技术设备)是用于访问memory设备(ROM、flash)的Linux的子系 统。MTD的主要目的是为了使新的memory设备的驱动更加简单,为此它在硬件和上层之间提供了一个 抽象的接口。MTD的所有源代码在/drivers/mtd子目录下。我将CFI接口的MTD设备分为四层(从设备节 点直到底层硬件驱动),这四层从上到下依次是:设备节点、MTD设备层、MTD原始设备层和硬件驱 动层。
linux-character-driver
- Linux下的简单字符设备驱动的源码,有说明文件说明如何编译和安装卸载测试驱动
hello_v2.6
- Linux 2.6版本下的简单的字符设备模块示例
hello_v2.4
- 支持Linux 内核2.4版本的字符设备模块示例
LINUX_driver_for_Char_dev
- linux2.6中底层驱动编写字符设备驱动源码。附有注解。
char_dev.tar
- 这个是linux下的一个字符设备的驱动程序,里面包含了驱动模块和测试用的驱动程序,在s3c4410开发板上验证过的,有问题联系作者qq:9460841
schar
- linux下字符设备的驱动程序.2.4 内核通过-character device driver through 1.2.4 kernel
os0201郑章孝
- .添加系统调用.采用编译内核的方法,添加一个新的系统调用 编写一个应用程序,测试新添加的系统调用 系统调用的功能:文件拷贝.2添加设备驱动程序.采用模块方法,添加一个新的设备驱动程序要求添加字符设备的驱动 编写一个应用程序,测试添加的驱动程序. 4分析/proc文件.监控系统状态,显示系统中若干部件的使用情况 用图形界面显示系统监控状态。
test1_src
- linux下的基本虚拟字符设备驱动程序,以模块的形式提供。-the basic characters of virtual device driver to the form module.
卸载
- 用特定函数实现驱动的卸载。该程序是字符设备驱动程序的框架卸载。-used to achieve specific function-driven unloading. The program is character device driver framework unloading.
scull-kfifo
- LINUX 驱动入门 字符设备 从入门到提升之 mydve_kfifo-linux driver primer
dev_add
- Linux简单字符设备驱动编写方法 本示例代码实现了Linux下的一个简单字符设备驱动。 由二个文件组成,驱动模块<dev_add.c>和测试程序<test.c>。-Linux character device driver writing simple method The sample code implements a simple under Linux character device drivers. Composed
LINUX_module
- 一个可以成功编译的LINUX字符设备源码,做课程设计的同学可以参考下!-LINUX can be successfully compiled a character device code, so students can refer to the curriculum design under!
s3c2440spi1
- S3C2440外设SPI1接口驱动程序模块,在linux2.6.32内核上运行通过,加载该模块后会在/dev/下生成一个SPI1字符设备文件,源内核有SPI子系统,不过太复杂,没去研究,所以就自己写了,绝对是原创,适合初学者参考。-S3C2440 SPI1 peripheral interface driver module, run by the linux2.6.32 kernel, load the module in the/dev/SPI1 generate a character d
watchdog
- s3c2410看门狗的字符设备驱动,可以在ubuntu中编译-s3c2410 watchdog character device driver, you can compile in ubuntu
2440_gpio
- linux下2440的gpio驱动,里边有一些含有内核中的注释,是看后的笔记,看这个对了解基本的字符设备的驱动写法有帮助-2440 under the GPIO linux driver inside the kernel contains some of the notes, is to look after the notes, look at this to understand the basic character device driver writing help
s3c2410-linux-2.6.11.1-apm-08.11.02
- 将s3c2410-linux-2.6.11.1-apm-08.11.02.patch复制到内核根目录。 执行patch –p1 < s3c2410-linux-2.6.11.1-apm-08.11.02.patch即可! 在2.6.11.1内核中,创建字符设备的代码是:linux/arch/arm/kernel/amp.c。在根文件系统创建设备节点是dev/misc/apm_bios。-Will s3c2410-linux-2.6.11.1-apm-08.11.02.patch c
led
- uclinux字符设备驱动编写的基本原理和过程,帮助刚刚入门的朋友一点提示-uClinux character device driver to prepare the basic principles and processes to help a friend that just getting started tips