搜索资源列表
dingshiqi
- 99秒秒表设计,1开始时,显示“00”,第一次按下sp1后就开始计时;2第二次按下sp1后,计时停止;3第三次按下sp1后,计时归零-99 seconds stopwatch design, a beginning, show " 00" , the first time after the beginning of press sp1 2 second press sp1, the time to stop 3 sp1 the third press, the time z
dianzimiaobiao
- 微机原理课程设计 8253电子秒表实验报告-sdadafafffcafa
miaobiao
- 凌阳单片机SPCEO61A实现的基本的秒表功能,能想裁判使用的那种计时器一样有计时功能。-Sunplus microcontrollers SPCEO61A to achieve the basic stopwatch functions, can be used to judge the kind of timer as a timer function.
multisim
- 基于Multisim软件设计的数字秒表电路课程设计报告-Multisim software design based on digital stopwatch circuit course design report
part2.6_1
- 利用定时器产生一个0-99s变化的秒表 并显示在数码管上 每过一秒将这个变化写到AT24C02内部储存 再次上电时 单片机直接读AT24C02里的数据-Use the timer to generate a change in 0-99s and displayed on the digital stopwatch on this change with every passing second internal storage re-write AT24C02 microcontroller
stopwatch
- 51单片机实现秒表,电路图和汇编源程序。-51 MCU stopwatch, schematic and assembly source.
time
- 电子钟 带proteus仿真 能够实现闹钟和秒表功能的-Proteus simulation clock with alarm and stopwatch functions to achieve the
stopwatch3
- 基于C51单片机的跑秒表,通过KEIL开发环境编译,软仿真可以实现-this is stopwatch for C51,i think it is ok.............
1602
- 用1602显示的秒表,支持按键修改成当前时间。-The stopwatch display with 1602, support key changes to the current time.
Digital-stopwatch-design
- 数字秒表的设计报告,用VHDL语言编写程序,实现分析讨论中各种功能,分别进行编译并生成相应的模块,然后将这些模块连接起来形成电路图,并进行编译、仿真。-Digital stopwatch design reports, using VHDL language programming, analysis and discussion of various functions to achieve, respectively, to compile and generate the correspo
Electric_clock_design_with_VHDL
- 本次设计的电子钟具有正常计时,时间手动设置,闹钟,秒表四种功能,能够输出24小时制的时间。 电子钟上电reset后,即以默认设置的时间00:00:00开始正常计时,工作模式为计时模式。mode键是工作模式切换键,按照计时—设置—闹钟—秒表四种模式一次切换。在正常计时模式下,按一下mode键切换至设置模式,left和right键用来调整小时或分钟使能被设置,up和down键用来调整时间,调整单位是1;设置好时间后按start_stop键确认(此处使用start_stop键作为ok键使用)。闹钟
基于单片机秒表系统设计
- 基于单片机课程设计_秒表系统设计(汇编),其中有设计介绍及用汇编语言写的关于数字秒表的程序-Based on the microcontroller course design _ stopwatch system design (assembly), which design introduced a program written in assembly language on digital stopwatch
AB3
- 只通过移位寄存器来实现AB两个按钮对秒表的单次计时功能和总计时功能两种功能(Only through the shift register to achieve AB two buttons, stopwatch single time function and total timing function of two functions)
ARM实现秒表功能
- 实现秒表功能。数码管高两位显示秒,低两位显示精确到0.01秒的数值(提示,修改PIT0中断的时间,调整走时和显示算法;在实现自由走时的基础上,利用按键,使其具有开始、暂停、继续、停止等功能。开始键负责清零,然后开始计时。(Stopwatch function. Two digital tube display seconds, low two digit display accurate to 0.01 seconds (numerical prompt, modify the PIT0 int
秒表
- labview秒表程序,可以定时,可以读秒。(the program of clock)
Android项目源码支持闹钟秒表倒计时的小明闹钟
- 简单闹钟实现,可以实现秒表,计时等一些功能。(Alarm clock, stopwatch, timer.)
danpianji
- . 应用MCS-51单片机设计电子秒表电路; 2. 选用4位LED数码显示,计数时间0-9999s,定时时间可调; 3. 硬件设计根据设计的任务选定合适的单片机,根据控制对象设计接口电路。设计的单元电路必须有工作原理,器件的作用,分析和计算过程; 4. 软件设计根据电路工作过程,画出软件流程图,根据流程图编写相应的程序,进行调试并打印程序清单; 5. 原理图设计根据所确定的设计电路,利用Protel等有关工具软件绘制电路原理图、PCB板图、(Design of electronic st
秒表
- 一个labview的秒表程序,实现基本的秒表功能(A stopwatch program LabVIEW, to achieve the basic stopwatch function)
秒表
- 实现以10毫秒为单位秒表计时,注释清晰易读(Achieve a stopwatch in 10 milliseconds.The notes are legible.)
miaobiao
- 简易秒表,用stc89c52主控制,数码管显示(Simple stopwatch with stc89c52 master control, digital tube display)