搜索资源列表
AT.pdf.tar
- GSM Model的AT指令集,可以通过window的超级终端或者linux的minicom来执行这些命令-GSM Model of the AT command set, you can window or linux of the Super Terminal minicom to run these commands
week9
- 通过串口输出“hello",在超级终端可以接收到,波特率设置为19200bit即可。-chuan kou tong xin
SerialPort_Control
- 一个非常简单的超级终端程序。希望对大家有用-HyperTerminal is a very simple procedure. Hope to be useful
spi_mifarc
- LM3S6952控制射频卡FM1702读取卡的信息,然后在超级终端显示卡片信息程序-LM3S6952 read FM1702
FLEXISJMSD_CDC_FAT
- 使用freescale 8位芯片MC9S08JM60,FAT16文件系统,使用超级终端读写SD卡,带有SD驱动,SPI驱动,USB mini stack等-SD card CDC demo FAT16 using USB terminal MC9S08JM60
demoXEPADC
- 飞思卡尔单片机AD转换程序,本程序完成下列功能的程序设计:单片机轮流采集通道0和通道1的模拟电压,把转换得到的数值转换成对应的电压值发送到串口显示出来,比如本次采得通道1的值为0x80,0x80代表的电压值为(0x80/0xff)*5=2.51伏(保留两位小数),则应在PC机超级终端收到数据“通道1电压值2.51伏”,单片机每0.5秒发送一次采集结果。-Freescale
watchdog_test
- 看门狗定时器程序,在PC 机的超级终端的主窗口中观察实验的结果-Watchdog Timer Program, in PC-HyperTerminal main window observed experimental results
Freescale
- 利用飞思卡尔实现超级终端传输,可以显示汉字等功能-Freescale to achieve transfer using HyperTerminal, you can display Chinese characters and other functions
superconsole
- 51单片机超级终端(c语言) 超级终端主函数,移植时需要重写几个初始化函数 * //* designed by fk at heu-51 SCM HyperTerminal (c language) HyperTerminal main function, transplantation needs to be rewritten several initialization function*//* designed by fk at heu
8951_232
- 单片机与pc通信,能通过超级终端显示菜单,并接受用户命令,与用户交互。-51 communitate with PC through 232
WAVECOM_AT_V90
- WAVECOM模块,短信猫指令开发资料,可用超级终端测试,成功后再编写代码。-WAVECOM module, development of data messaging cat command can be used HyperTerminal test, after successfully writing code.
lm3s1138_adc
- 基于《Stellaris外设驱动库》的例程:处理器直接触发ADC采样 本实验演示配置ADC采样序列0,通过处理器直接触发ADC采样,ADC模拟量需从外部输入(ADC0),最大不能超过3.0V,因为ADC内置的参考电压为3.0V。 在进行ADC配置之前,必须首先进行PLL锁相环配置(详见EasyARM1138例程\02 SysCtl(系统控制)\3 锁相环PLL设置)。错误配置PLL将使系统进入异常。 ADC采样得到的数字量将利用超级终端从串口读出 。本开发板采用US
quad_ask_system
- 4路抢答器 !试发 用超级终端通讯实现电脑显示功能,是基于msp430 实现的单片机作品!-4 Way Responder! Examination of hair to achieve the HyperTerminal communications computer display, is based on the realization of the microcontroller msp430 works!
hype
- win7系统下的超级终端 win7下没有超级终端它可以代替-win7 systems under win7 HyperTerminal HyperTerminal can not substitute
UART
- S342410裸机串口C编程,实现发送字母到超级终端,终端会显示-S342410 bare metal serial port C programming, sent letters to the HyperTerminal, the terminal will display
STM32-RTC-V2
- RTC模块的当前时间通过串口传送给PC机的超级终端显示,若RTC模块还未设置时间则通过超级终端进行设置。RTC秒中断每发生一次,发光二极管LED1闪烁一次。-RTC module to send the current time through the serial port PC-HyperTerminal shows that if RTC module is not yet set the time set by the Super Terminal. RTC seconds interr
6
- 串口通讯实验: 本实验得到的结果为,打开超级终端,设置波特率为115200,数据流控制位为无。运行系统,就会显示“UART & Interrupt Experiment,Please Input from the keyboard”,我们就可以通过写串口操作。 在flash调试时,需要修改RO BASE为0x00000000,其他不用修改,重新编译下载就可运行。 注意:由于系统产生中断,程序计数器就会跳到0x18处执行中断服务子程序,所以不能在SDRAM调试。 -Ser
SecureCRT-v6.58H
- 强大的嵌入式“超级终端”,比Windows的超级终端强大。而且操作简便-qiangdade chaojizhongduan .windows.
STM32_UART_printf_scanf
- STM32F103ZE串口测试程序,可以通过超级终端输出和输入数据,此程序完整可用。-STM32F103ZE serial port test program, you can output and input data HyperTerminal, the integrity of the process is available.
SuperTerminal
- windows7没有附带超级终端,可以用这个,很不错的工具-windows7 HyperTerminal is not included, you can use this, it is a good tool