搜索资源列表
ads1115
- 使用LM3S8962控制ADS1115,实现AD采集。-Use the LM3S8962 control ADS1115, AD collection.
rtt_iar
- rt-thread 在TI LM3S8962上的移植，IAR6.00以上版本均可，里面包含了LWIP协议栈-rt-thread transplant TI LM3S8962 versions can IAR6.00 above, which contains of the LWIP protocol stack
UART_FIFO
- LM3S8962中成功实现UART的FIFO功能的程序-The LM3S8962 successful program the UART FIFO
LM3S8962-drive-731
- LM8942芯片的底层双路电机驱动电路板的嵌入式程序，通过串口通信接受上位机发送的控制指令，输出PWM波形对电机调速，然后通过QEI模块读取双路编码器信息上传给上位机-LM8942 the underlying chip dual motor drive circuit board embedded programs, accept control commands sent by the host computer, the output PWM waveform of the motor s
Serial
- 基于Labview的嵌入式ARM开发套件，具体型号是LM3S8962，此代码是ARM与上位机的串口通信程序-Specific models based on Labview embedded ARM development kit, LM3S8962, code ARM serial communication with the host computer program
QEI
- 基于Labview的ARM嵌入式开发，基于LM3s8962开发板，QEI编码器模块的初始化与数据的读取-Labview-based ARM embedded development, based on LM3s8962 development board, the QEI encoder module initialization data read
JTAGTOGPIO
- 本程序为ARM lm3s8962对JTAG引脚做GPIO功能转换的程序-This procedure the for ARM lm3s8962 of JTAG pins do GPIO function to convert the program
Uart_Driver
- 本程序为ARM的LM3s8962单片机的uart驱动测试程序-The procedures for the the ARM-LM3s8962 microcontroller uart driver test program
RS485
- 本程序为ARM的LM3S8962的485串口通讯测试程序 -The program for the the LM3S8962 ARM-485 serial communications test program
I2C
- 本程序为ARM的LM3S8962单片机的I2C测试程序-This program ARM LM3S8962 microcontroller' s I2C test program
ADC
- 本程序为ARM的LM3S8962的ADC测试程序-This program is the ARM LM3S8962 ADC test program
CANRcv_snd
- 本程序为ARM的LM3S8962的can总线通信程序-The program for the ARM LM3S8962 can bus testing program
24C02Program
- 本程序为ARM的LM3S8962的eeprom编程器测试程序-This program is the ARM LM3S8962 eeprom programmer testing procedures
sd_SPI
- 本程序为ARM的LM3S8962的SPI测试程序-The program for the ARM LM3S8962 SPI test program
Helloworld
- lm3s8962的helloworld程序-helloworld program of lm3s8962
ADC
- LM3S8962 ADC采样程序 调试成功-LM3S8962 ADC sampling program debugging success
driverlib
- lm3s8962的库函数全集，囊括了各种常用的函数说明。-lm3s8962 Complete Works of library functions
The-Comunication-of-LM3SPlwip-UDP
- 实现LM3S8962与上位机的UDP通信，内含VC界面，可调试。-LM3S8962 UDP communication with the host computer, containing VC interface debug.
my-send_recv
- 本程序使用C语言，实现了KEIL MDK编译环境下对LM3S8962类型MPU的串口发送和读取消息-It used C in KEIL MDK and LM3S8962 MPU to fulfill to task of sending messeges by Universal Asynchronous Receiver/Transmitter method.
LM3SAPP_CAN_BaudRate_Set
- 1.开发板:EasyARM8962，CPU:LM3S8962，外部晶振6MHz。 应用于其他开发板或CPU Pack时应作适当修改。 2.该范例程序演示了通过USBCAN,开发板与PC机进行CAN通信。波特率为500K。 3.开发板工作于镜像模式：收到数据帧则返回相同的数据帧；若收到远程帧， 则返回长度为0的数据帧。 4.数据帧接收不使用“验收滤波”，远程帧接收滤波的标识字符为0x123。 5.编译环境 IAR Embedded Workbench 5.11 -1