搜索资源列表
NCO_sine_gen
- 用Simulink中NCO模块产生正弦信号的程序，自己写的，采样率180MHz，正弦频率70MHz，可以直接运行。-Using Simulink module generates a sinusoidal signal of NCO program, sample rate 180MHz, sinusoidal frequency 70MHz, can be directly run.
eetop.cn_FYP_V2
- 基于cordic算法的nco仿真完整matlab程序-nco cordic algorithm simulation
nco
- 利用数字振荡器产生一个正弦波。修改参数可以修正弦波频率幅度相位。-Using the digital oscillator generates a sine wave. Modified sine wave frequency parameters can be modified amplitude and phase.
dds
- NCO，同时产生cos和sin信号。quartus -NCO, while producing cos and sin signals. quartus II
Filtro-3-vias
- This a model of a QPSK modulation system for transmission over a bandpass channel with fc = 100 Hz and B = 30 Hz and AWGN at the receiver. SRRC fi lters with excess bandwidth α = 0.18 are employed. The receiver includes an NDA timing recovery lo
nco_program
- 数字控制器频点调整，包括频点上移动或者向下移动的程序-digital nco
NCO_test
- FPGA的压控振荡器NCO完整Verilog工程代码，测试输出1KHZ sin波。signaltap抓取没问题。-VCO NCO complete FPGA Verilog code engineering, test output 1KHZ sin wave. signaltap crawl no problem.
NCO
- 基于FPGA的DDS设计，通过外接DA转换器输出稳定的正弦波，方波和三角波，可单独产生时钟，不必借助硬件连接，包含寄存器程序，累加器程序和时钟发生电路等，以及顶层设计原理图-The DDS FPGA-based design, through an external DA converter output stable sine wave, square wave and triangular wave, can produce a single clock, without the help
my_nco-(1)
- A basic Direct Digital Synthesizer consists of a frequency reference (often a crystal or SAW oscillator), a numerically controlled oscillator (NCO) and a digital-to-analog converter (DAC) [3] as shown in Figure 1. The reference oscillator provid
NCO_DDS
- 自己写的代码，用了NCO核组合的DDS，测试过，希望对大家有所帮助-Write your own code, using a combination of NCO nuclear DDS, tested, we hope to help
dpll_fixpt
- a simulink model for DPLL with NCO
codegen
- GPS接收中关于码的产生、通道的选择、码DCO-code generate、tracking channel、code nco
carriergen
- GPS接收机设计中关于载波的产生、载波数控振荡器-carrier mixer、carrier nco
gensin
- 用fpga控制da发一定带宽正弦信号，用vhdl编写，用nco-Fpga controlled by a band-da made a sinusoidal signal, written in vhdl, with nco
DDC
- matlab 编写的简单数字下变频仿真程序，含NCO模块、混频、低通滤波、抽取。模块大多采用matlab自带函数实现- program for DDC simulink base on Matlab
cordic
- verilog编写的数字信号发生器NCO用CORDIC方法实现产生sin cos信号，流水线结构，简单实用。-verilog prepared by the digital signal generator NCO using CORDIC method implementation generate sin cos signal, pipelined architecture, simple and practical。
ddc
- 数字下变频matlab代码，包含NCO、混频、抽取、低通滤波器部分的仿真-DDC matlab code, including NCO, mixing, extraction, simulation, part of the low-pass filter
DCO
- 数控振荡器：可根据输入相差改变频率控制字，产生一组正交的正弦波,SIMULINK 模型-DCO/NCO
ASKMod
- 基于FPGA的ask调制程序，包括载波的生成，nco的设置-FPGA-based ask modulation procedures, including carrier generation, nco settings
AskDemod
- 基于FPGA的ask解调程序，包括载波的生成，nco的设置-FPGA-based ask demodulation process, including the carrier generation, nco settings