搜索资源列表
ask_fsk
- 数字通信系统振幅键控ASK信号和频移键控FSK的调制与解调的VHDL代码-ASK amplitude shift keying digital communication system signal and the frequency shift keying modulation and demodulation of the VHDL code for
scrambler
- 数字通信的扰码程序,保证二进制01的数量基本相同-Digital communications scrambler procedures to ensure the same number of binary 01
UART
- 用FPGA开发的串口通信的程序,代码是用verilog编写的,希望对大家有用!-Serial communication with the FPGA development process, the code is written in verilog and hope for all of us!
DS18B20
- 8位单片机与DS18B20并行双向通信。 Quartus II 8.1项目工程文件. 主源程序文件为DS18B20.v,里面有详细注解。 例子: DS18B20 数据地址 0xf000(ROM=0) DS18B20 ROM指令地址 0xf001(ROM=1) 外部电源供电且只有一DS18B20的读取法: 发送CC到0xf001, 等待busy=0说明器件已准备好, 读0xf001的Bit1=1说明存在器件,Bit0=1为控制忙(可以省略此步) 发送44
SPI
- SPI(Serial Peripheral Interface)是一种串行同步通讯协议,由一个主设备和一个或多个从设备组成,主设备启动一个与从设备的同步通讯,从而完成数据的交换。SPI 接口由SDI(串行数据输入),SDO(串行数据输出),SCK(串行移位时钟),CS(从使能信号)四种信号构成,CS 决定了唯一的与主设备通信的从设备,如没有CS 信号,则只能存在一个从设备,主设备通过产生移位时钟来发起通讯。通讯时,数据由SDO 输出,SDI 输入,数据在时钟的上升或下降沿由SDO 输出,在紧接着
IICbus
- 基于nios ii 控制altera de1 开发板上iic总线实现与at24c02通信-Based on nios ii controlled altera de1 Development Board iic bus for communication with the at24c02
PC
- 在quartus下实现了PC机的串口通信功能-The quartus achieve the PC-Serial communication function
8251
- 在MAXPLUX下实现8251串口通信功能-The MAXPLUX achieve 8251 serial communication
NRF905
- 基于430的nrf905通信代码里面还带有gsp定位系统-Based on 430 of the communication code inside the nrf905 positioning system also features a gsp
ds32c35
- ds32c35是dalas生产的实时时钟(RTC)芯片,本程序(在EP2C8Q208C8N上调试通过)在FPGA上构建I2C接口于此时钟芯片通信。可以在LED上动态实时显示时间。利用本程序也可以改编成高精度实时时间测量的程序-ds32c35 is produced by dalas real-time clock (RTC) chip, this program (in the EP2C8Q208C8N debugging via) in the FPGA built this clock ch
interface
- 采用Cyclone EP1C3,VHDL程序算法实现了信号波形的实时采样并回放,同时能测量时域信号的频率,通过与MCU的8位并行接口,进行相互通信。-Using Cyclone EP1C3, VHDL program algorithm of the signal waveform of real-time sampling and playback at the same time capable of measuring the frequency of the signal in time
fangz
- 数字通信系统的仿真,包括调制解调,上下变频,加入了高斯白噪声,并且每个步骤都生成相应的图形-Digital communication system simulation, including the modulation and demodulation, the upper and lower frequency, by adding Gaussian white noise, and each step generates the appropriate graphics
uart
- 程序说明: 本次实验控制开发板上面的串口,与PC机进行通信,并在串口精灵里面显示字符。 目录说明: 工程在\project文件夹里面 源文件和管脚分配在\rtl文件夹里面 下载文件在\download文件夹里面,.mcs为PROM模式下载文件,.bit为JTAG调试下载文件。-Procedure Note: The experimental control development board above the serial port to communicate wit
usb
- 程序说明: 本次实验控制开发板USB,与PC机进行通信,并在显示字符。 目录说明: 工程在\project文件夹里面 源文件和管脚分配在\rtl文件夹里面 下载文件在\download文件夹里面,.mcs为PROM模式下载文件,.bit为JTAG调试下载文件。-Procedure Note: In this experiment, control development board USB, and PC, to communicate, and display char
l602display
- 1602显示单片机与FPGA的通信!实现数字钟的功能!仅供参考!望大家多多指教-desplay1602
IIC
- fpga实现的IIC通信的例程,注释很详细-fpga implementation of serial communication routines, comments in great detail
Interface
- 已在实验箱上验证,目标芯片EP1C3T144C8 十位全时双工串行通信接口-Interface
DHT22_v1.1
- 我以前曾发过V1.0版的,这是此版的修正版v1.1,修正了以前版本中的一个错误,即只能读一个数据后就再也读不出温度数据的错误。 这个是用Quartus II软件写的Verilog HDL语言写的与温湿度传感器DHT2x通信的代码. 里面有详细的注解. 主要用于DHT2x单线总线通信转换为8位并行总线通信,应用于具有外部8位总线访问功能的单片机直接读取温湿度数据. 此程序在EPM7128SLC-10中成功测试. -I' ve once spoke V1.0 version, whic
SLAVE_FIFO_16BITS
- 68013和FPGA通信 含有68013 slave firmware 含有FPGA VHDL程序-communication between 68013 and FPGA including 68013 slave firmware including FPGA VHDL code
FPGA
- 使用VHDL实现的串口通信程序,主要完成利用串口收发数据等功能 -Using the VHDL implementation of the serial communication program, primarily the completion of functions such as send and receive data using serial port