搜索资源列表
4.5_V_TO_52_V_INPUT_CURRENT_MODE_BOOST_CONTROLLER.
- 4.5伏到52伏输入电流模式升压控制器，是美国德州仪器公司的一个很好用的电流控制芯片-4.5-V TO 52-V INPUT CURRENT MODE BOOST CONTROLLER
28335_mppt
- 4路pwm，buck升压，错相抑制电流脉动-4 pwm, buck boost, current ripple-phase inhibition
C3D04060E
- 600-Volt Schottky Rectifier • Optimized for PFC Boost Diode Application • Zero Reverse Recovery Current • Zero Forward Recovery Voltage • High-Frequency Operation • Temperature-Independent Switching Behavi
1871
- 只电流模式升压芯片,需要极少外部元件的宽输入，电流模式、升压、反激和SEPIC控制器-Only current-mode boost chip requires minimal external components of wide input, current mode, boost, flyback and SEPIC Controller
1
- 提出了一种新型的单开关升-降压式(Buck-Boost)直流变换器的电路仿真平均模型。这种模型可通过输 入参数的选择实现对Buck-Boost电路的电压控制、峰值及平均电流控制,以及对DCM-CCM工作方式的统一。它 是一种实用的仿真模型,可方便地进行稳态和动态分析。在保证准确的基础上,大幅度提高了仿真的速度,通常比 用实际器件开关电路的仿真速度提高两到三个数量级。 -A novel average model for single switch Buck-Boost DC/DC
ADC_CC2
- 英飞凌单片机XE162的开发应用，能够使得boost电路的电压完成PID控制，并且有电压电流采样-Chip XE162development and application, can make boost circuit voltage PID control, and the voltage and current sampling
boost_current
- boost电路matlab仿真 采用电流闭环-boost circuit the matlab simulation using current closed loop
new1
- boost电路matlab仿真，输入为带有波动的直流电压 要求占空比为0.5-boost current road
i_t_1int
- current in boost cover.
My_CS_mod3
- cs mod current in boost cover.
u_t_1int
- current in buck - boost cover.
final-res
- Grid-Connected Boost-Half-Bridge Photovoltaic Microinverter System Using Repetitive Current Control and Maximum Power Point Tracking
buck_boost
- DC-DC升降压电路,主要实现升压和降压功能，采用PI电压电流双环控制-DC-DC buck-boost circuit, the main step-up and step-down function, using the PI voltage and current loop control
BoostPFC_using_average_current_Model
- 平均电流控制的boost pfc仿真 请用最新版本打开-Boost pfc average current control simulation
SD_power
- 本单相正弦波逆变电源的设计，以12V蓄电池作为输入，输出为36V、50Hz的标准正弦波交流电。该电源采用推挽升压和全桥逆变两级变换，在控制电路上，前级推挽升压电路采用SG3525芯片控制，闭环反馈；逆变部分采用驱动芯片IR2110进行全桥逆变，采用U3990F6完成SPWM的调制，后级输出采用电流互感器进行采样反馈，形成双重反馈环节，增加了电源的稳定性；在保护上，具有输出过载、短路保护、过流保护、空载保护等多重保护功能电路，增强了该电源的可靠性和安全性；输出交流电压通过AD637的真有效值转换后
bopi32
- 用MATLAB的simulink和simpowersystem，搭建一个BOOST电路。输入电压15~25V，输出电压40V，输出电流0.5A。-Using the MATLAB simulink and simpowersystem, build a BOOST circuit. Input Voltage 15 ~ 25V, output voltage 40V, output current 0.5A.
PRI
- In this paper, a simple single-phase grid connected photovoltaic (PV) inverter topology consisting of a boost section, a low-voltage single-phase inverter with an inductive filter, and a step-up transformer interfacing the grid is considered. Ideally
boost_peak_current_control
- Boost变换器的电流反馈控制，闭环系统，实用简练，好用。-Boost converter current feedback control, closed-loop system, practical and concise, easy to use.
ZSOURCEINVERTER
- This paper proposes an improved Z-source inverter topology. Compared to the traditional Z-source inverter, it can reduce the Z-source capacitor voltage stress significantly to perform the same voltage boost, and has inherent limitation to inrush curr
SMCGPV
- A boost converter is directly connected to the PV array with MPPT for operating at the maximum power point. A regulation cascades (current/voltage) applied using SMC for the control of DC converter a loop of voltage makes it possible to produ