搜索资源列表
hc11f1_i2c
- I2C bitbang master code for MC68HC11(F1) microcontrollers
ds2482
- ds2482.c - provides i2c to w1-master bridge(s).
PCF8591
- PCF8591是8bit的A/D和D/A芯片，采用i2c接口，它有四路模拟输入口和一个模拟输出口，采样速率取决于i2c的速率。数据传输是高位在前低位在后（不论是主机写入数据，还是主机读取的数据）。-PCF8591 is the 8bit A/D and D/A chip, using i2c interface, which has four analog inputs and one analog output sampling rate depends on the rate of i2c.
i2c_master_bit_ctrl
- I2C控制总线主机，按照字节写设计的verilog代码，由于选项中没有verilog这项，因此选择VHDL-I2C control bus master, according to the byte write verilog code design, because the option is not verilog this, so choose VHDL
pinmux-sh7269
- I2C multiplexer driver for PCA9541 bus master selector for Linux v2.13.6.
main
- stm8s M24C64 iic eeprom 源码-This firmware provides a basic example of how to use the I2C firmware library and an associate I2C EEPROM driver to communicate with an I2C EEPROM device (here the example is interfacing with M24C64 EEPROM) I2C per
i2c_gpsl30
- 按照一般字符驱动处理的 I2C驱动程序，没有使用i2c体系结构。实现了 从模式读，和主模式写的功能。-IIC device driver that slave receive model and master TX model。
Guitar_capacitive_screen_driver
- （Guitar电容屏驱动）多点电容式触摸屏控制芯片Guitar，采用投 射式电容检测原理，由15个驱动通道与10个感应 通道组成触摸检测网络，通过内置模拟放大电路、 数字运算模块，及高性能MPU得到实时准确的触 摸信息，并通过I2C传输给主控芯片。实现“所 点即所得”的非凡用户体验。 Guitar可同时识别5个触摸点位的实时准确 位置，移动轨迹及触摸力度。并可根据主控需 要，读取相应点数的触摸信息。-(Guitar capacitive screen driver
esp8266_i2c
- esp8266 i2c学习实例，可与其他具有i2c通信协议的设备进行通信，esp8266只能作为主设备-Examples esp8266 i2c learning to communicate with other devices with i2c communication protocols, esp8266 only as a master device
IO_simulate_I2C(masterPslave)
- 单片机IO口模拟I2C通讯,包含主模式和从模式-Microcontroller IO port simulation I2C communication, including master and slave modes
F0xx_SMBus_EEPROM
- 本程序是基于C8051F100的一个小程序，针对C8051F100的IO、时钟、中断等进行了初始化的设置，同时主要实现了SMBUS总线的控制程序，对于本单片机的学习比较有帮助。- This example demonstrates how the C8051F0xx ( F005 family) SMBus interface can communicate with a 256 byte I2C Serial EEPROM (Microchip 24LC02B). //- Interr
I2C_of_MSP430F249
- This demo connects two MSP430 s via the I2C bus. The master reads 5 bytes the slave. This is the MASTER CODE. The data the slave transmitter begins at 0 and increments with each transfer. The USCI_B0 RX interrupt is used to know when new data h
i2cslave_latest.tar
- opencore上的i2cslave ，也有相关master资料用于仿真(i2c slave download from opencore)