搜索资源列表
69478
- matlab programming for dc dc motor
Untitled DAB1
- 这是一个关于双主动桥的DC-DC逆变器的Matlab仿真(This is a Matlab simulation of a dual active bridge DC-DC inverter)
DPFC
- In this paper, we introduced a new series-shunt type FACTS controller called as distributed power flow controller to improve and maintain the power quality of an electrical power system. This DPFC method is same as the UPFC used to compensate the v
Rotor thrust calculator
- 该算法适用于各种转子采用无刷直流电机和ESC(显然)。 特别是本程序只适用与串口通信准备Arduino电路板。 你可以如果你没有Arduino开发板改变最初的声明。 从实际电机/转子u计算,必须有一个微控制器,将获得MATLAB命令,并将命令发送到特定的引脚上的ESC电机连接。请注意,引脚必须是一个PWM能力。(The algorithm is suitable for the use of Brushless DC motor and ESC (obviously) for variou
power electronics and systems
- 本书以MATLAB为基础,介绍了MATLAB电气系统模型库模块及其功能,并以实例介绍了电力电子和电机控制系统的建模和仿真方法,内容包括AC/DC、DC/DC、DC/AC、AC/AC的各种变换电路,直流调速系统和交流调速系统等。为了适应现代数字化控制系统的发展,本书在连续系统的建模仿真外,还介绍了采样离散系统的建模和仿真方法。(Power electronics and sysytem book simulink model)
brushlessDCmotor
- 无刷直流电机的控制系统,使用MATLAB建立的仿真模型。control of brushless DC motor(control of brushless DC motor)
motor_single_closed
- 通过工程设计法,设计双闭环参数,matlab仿真实现了直流电机电流转速双闭环控制。(Double closed loop control of current and speed of DC motor is realized)
singlephasedesign
- 该程序为MATLAB的m文件,用于设计单相LCL并网逆变器控制器参数,控制方式为电容电流和入网电流控制方式,只需输入LCL滤波参数和直流侧电压可计算出双闭环控制器参数。(The program is the m file of MATLAB, which is used to design the controller parameters of the single-phase LCL grid connected inverter. The control mode is the contr
交直流潮流算法统一法
- 一种交直流潮流计算程序,基于Matlab(A calculation program for AC and DC power flow)
BLDC
- 直流无刷电机速度电流双闭环仿真模型,基于matlab中的simulink仿真(Simulation model of speed and current double closed loop for brushless DC motor)
PWM直流脉宽调速系统建模与仿真
- 本文在介绍双闭环PWM直流调速系统原理基础上,根据系统的动、静态性能指标采用工程设计方法设计调节器参数,并运用Matlab的Simulink面向系统电气原理结构图的仿真方法,实现了转速电流双闭环PWM直流调速系统的建模与仿真。(This paper introduces the principle of double closed-loop PWM dc speed regulation system based on the adopted according to the static an
danxiangqiaoshi
- 不控整流仿真 1.在MATLAB/Simulink中搭建单相桥式不控整流电路仿真模 型; 2.仿真分析空载的直流电压波形、交流电流波形; 3.仿真分析带载的直流电压波形、交流电流波形; 4.选择合适的滤波电感电容参数,观察分析其对直流电压的 抑制作用。(先完成2、3,再进行第4步) 仿真参数:交流电压有效值220V,频率50Hz,R=50Ω(Uncontrolled rectification simulation 1. build a simulation module of
BLDC-DTC
- 这是关于无刷直流电机的DTC算法MATLAB验证。通过仿真效果很不错。(This is the MATLAB algorithm for the DTC algorithm of Brushless DC motor. The simulation results are very good.)
zonghe_try (1)
- 对铅酸蓄电池,超级电容,锂电池,三者连接到dc-dc变换器升降压,然后采取不同的控制策略,恒压,恒流,恒功率控制,最后通过逆变器将直流变交流。matlab 仿真(For lead-acid batteries, supercapacitors and lithium batteries, the three are connected to the dc-dc converter to increase and decrease the voltage. Then, different cont
myhallBLDC
- 直流无刷电机带霍尔传感器双闭环的MATLAB仿真,(MATLAB simulation of double closed-loop DC brushless motor)
MATLAB50
- MATLAB电机仿真精华50例,书籍,学习MATLAB电机仿真的好书,值得推荐,可配合《交直流调速系统与MATLAB仿真》使用(50 cases of MATLAB motor simulation essence, books, good books for learning MATLAB motor simulation, it is recommended, can be used with "AC and DC speed control system and MATLAB s
BLDC 完整
- BLDCM的simulink模型,电流、转速双闭环控制的无刷直流电动机系统,电机模块是自己封装而成的不是用的永磁同步电动机或者自带的BLDCM,所涉及的三个程序也有展示。(The model of BLDCM, the BLDCM system with double closed-loop control of current and speed,and the motor module is a self packaged permanent magnet synchronous motor
DCmotor
- 直流电动机的数学模型搭建,与matlab自带直流电动机模型进行对比。(The mathematical model of DC motor is built and compared with that of MATLAB.)
交直流混联系统统一迭代法-IEEE9
- 利用matlab进行编程,交直流混联系统9节点潮流计算程序(9-node power flow calculation program for AC / DC hybrid system)
Buck控制模型
- 自己做的Buck控制模型,输入48V DC,输出12V DC,电压电流双环控制。在Matlab 2014a的simulink下仿真,算法已经在实际工程中应用,可以供做算法研究人员参考。