搜索资源列表
triapf1
- 基于单位功率因数控制策略的三相全控整流。开关器件采用IGBT。PWM波形产生控制电路里使用的饱和限制模块，就是限制波形的幅度的，对输出直流电压幅值影响很大。-Based on the unity power factor control strategy of three-phase full-controlled rectifier. Switching device IGBT. PWM waveform generator control circuit in the saturation
081208
- 基于MATLAB软件的交流永磁同步电机调速系统研究 介绍了一种采用磁场定向理论控制交流永磁同步电机的调速系统，应用现代控制理论对 电机直交轴耦合分量进行了解耦，并利用经典控制理论设计了电流环和角速度环调节器。MATLAB 仿真 结果证明了该方法的有效性，但系统调试时仍需根据具体情况适当调整以得到更理想的效果。-MATLAB software based on the exchange of permanent magnet synchronous motor speed contro
ACtoDC
- this file is AC to DC converter
InverterSPWM
- AC to DC converter
zlddjzjtxcs
- 利用MATLAB语言编写的直流电动机转矩特性测试程序-The use of MATLAB language features of the DC motor torque test procedure
zlddjzd
- 利用MATLAB语言编写的直流电动机制动特性分析的程序-The use of MATLAB language of DC motor braking characteristics of process
ex6
- it is used to control the dc motor by using fuzzy logic controllers
1_speed_control_pid
- 这个源码，将使用模式，制定从一个粗略模型到一个基于PID的负载直流电动机控制系统的离散实施。-In this chapter we will use model elaboration to go from a crude model to a discrete implementation of a PID based control system for a DC motor with load.
murali_Matrix_Converter_3phase
- it is the simulation of matrix converter with motor load. matrix converter is an upcoming popular converter from ac to ac with out use of dc link.
Simulation_of_BLDC
- this simulation is of the Brushless DC motor and the implementation is done by using matlab-this simulation is of the Brushless DC motor and the implementation is done by using matlab...
BLDCM
- 无刷直流电动机模型 包括：逆变器模块、电源模块、换相逻辑模块、PWM信号产生模块、电动机本体模块、转速测量模块和磁极位置测量模块。-Brushless DC motor model includes: inverter module, power module, commutation logic module, PWM signal generation module, motor body module, speed measurement modules, and pole posi
H_bridge
- H桥控制的simulink仿真模型，可以作为直流电机控制系统设计的参考模型-H-bridge control of the simulink simulation model can serve as a DC motor control system design reference model
flc
- fuzzy logic control DC motor
DC_res_start
- This folder has two files for the simulation od dc motor resistive starting. please run the *.m file to run the *.mdl file-This folder has two files for the simulation od dc motor resistive starting. please run the*.m file to run the*.mdl file
DC_motor_brak
- This folder has two files for the simulation of dc motor braking. please run the *.m file to run the *.mdl file-This folder has two files for the simulation of dc motor braking. please run the*.m file to run the*.mdl file
se_ge_no_load
- 关于直流电机的空载特性的matlab仿真，采用的是样条插值算法对曲线进行拟合，初学者可以改为其他拟合方式看结果如何-With regard to the no-load characteristics of DC motor matlab simulation, using the spline interpolation algorithm, beginners can be fitted into other ways to see the results
Chopper_and_inverters
- it describes about the power electronic components dc/dc converters and 3 phase inverters.it has the matlab files in zip file
double15
- 直流电机的双闭环调速系统的matlab仿真模型，mdl文件-a double closedloop speed regulation matlab model of DC machine
power_converter_craig_no_Trans
- This power converter in matlab with no transformer. The full control is using. PID controller for the gating signal of SCR. The phase angle has been controlled-This is power converter in matlab with no transformer. The full control is using. PID cont
start
- 直流电动机 降压软启动 simulink模型 参考-Step-down DC Motor soft-start simulink model reference