搜索资源列表
bianmakaiguan
- 本代码为编码开关代码,编码开关也就是数字音响中的 360度旋转的数字音量以及显示器上用的(单键飞梭开 关)等类似鼠标滚轮的手动计数输入设备。 我使用的编码开关为5个引脚的,其中2个引脚为按下 转轮开关(也就相当于鼠标中键)。另外3个引脚用来 检测旋转方向以及旋转步数的检测端。引脚分别为a,b,c b接地a,c分别接到P2.0和P2.1口并分别接两个10K上拉 电阻,并且a,c需要分别对地接一个104的电容,否则 因为编码开关的触点抖动会引起轻微误动
bianmaqi
- 旋转光电编码器的单片机借口及某型号单片机的c程序,好资料-Rotary optical encoder and a model of SCM SCM pretext c procedures, good information
ROTARY_KNOB
- Rotary knob/encoder reader
GpioShuttle
- Module for gpio Rotary Optical Encoder Bourns EM14
DDS_Board_Encoder
- DDS AD9850 LCD1602 编码器 代码支持STC单片机,旋转编码器正反测试OK,2种步进测试-DDS AD9850 LCD1602 encoder code support STC microcontroller, rotary encoders, both positive and negative test OK, two kinds of stepping test
spin_sram
- 基于keil5的stm32板的开发,此程序重点在于对旋转的编码的定时器设置,和处理旋转编码器的状态,非常实用。-Stm32 based development board keil5, the program focuses on the rotary encoder timer settings, and state processing rotary encoder, very practical.
2313
- Rotary encoder attiny winavr
power
- power STC15F204EA rotary encoder version of white T12 controller
51单片机检测光电旋转编码器每周实际脉冲数
- 51单片机检测光电旋转编码器每周实际脉冲数(The single-chip microcomputer detects the actual pulse number of the photoelectric rotary encoder)
I2C1602完整驱动程序1
- STM32通过I2C总线驱动1602显示屏以及使用旋转编码器实现数值增减(The STM32 drives the 1602 display via the I2C bus and uses a rotary encoder to increase or decrease the value)
电子钟
- 基于51单片机的电子钟,可通过EC11旋转编码器修改时间,LCD1602显示时间。 时钟精度可通过T0定时器的初值来调节,但是要实现高精度晶振的关系非常大,本程序只是粗略的进行电子钟的仿真,如果要实现高精度还是要用其他外接模块来配合。(Based on 51 microcontroller electronic clock, can be modified by EC11 rotary encoder time, LCD1602 display time. The clock accurac
bianmaqi
- 通过旋转编码器模块,可以实现1602液晶显示器数字上的加减(Through the rotary encoder module, 1602 LCD display can be added and reduced)
ENCODER_EC11
- 基于STC15单片机的EC11旋转编码器驱动程序。支持一定位对一脉冲或两定位对一脉冲的两种规格EC11。并实现旋转编码器按键单击双击长按功能(EC11 rotary encoder driver based on STC15,Two kinds of specifications for one pulse or two positioning to one pulse for certain bits EC11. And realize the rotary encoder click, do
然并卵的灯
- 功能 1、单键开关LED 2、在LED开启状态下旋转编码器可以调节pwm以控制LED亮度 3、在LED开启状态下双击达到最大亮度(实际就是程序事先设定好的) 4、在LED开启状态下长按进入延时关断,延时65s,最后10s指示灯闪烁 5、在延时关断状态下单击取消延时关断 6、关断或者掉电后会记忆最后亮度(掉电记忆) 注: 1、短按操作:按键按下,按下时间<1s,属于一次短按操作 2、长按操作:按键按下,按下时间>1s,属于一次长按操作(The function of
control_DOBPos2
- this is arduino due code. im using rotary encoder on motor shaft and for add/reduce set point. the motor rotary encoder assigned in pin 2 and 3 arduino
旋转编码器
- 关于EC11旋转编码器计数的程序,使用STM32F103系列,可以用KEIL打开(On the EC11 rotary encoder counting procedures, the use of STM32F103 series, you can use KEIL to open.)
STM32F103-OLED-Menu-master
- EC11旋转编码器控制0.96寸OLED的多级菜单(EC11 rotary encoder controls 0.96 inch OLED multi-level menu)
stm32f407编码器模式
- 在stm32F407的基础上实现旋转编码器的控制并通过串口显示数据(Based on stm32F407, the control of rotary encoder is realized and data is displayed through serial port.)
1-2-18-旋转编码器数码管显示程序
- STM32 旋转编码器数码管显示程序,已经调试通过(STM32 rotary encoder digital tube display program, has been debugged and passed)
_IEEE802.11ad标准中LDPC编译码的研究
- 首先,认识标准。从系统层面和物理层两方面介绍此标准,给出标准的发送端和接收端系统结构框图,重点描述标准中物理层的特征,总结出标准的重要特点和关键技术。 其次,研宄和实现两种编码器。根据标准中码矩阵的特点,设计一种高效的编码器,完成的实现。在此基础上提出一种新的编码结构一旋转码,对旋转编码器结构进行探究,完成它的仿真和实现。(First of all, recognize the standard. This paper introduces the standard from two aspec