搜索资源列表
stm32-Encoder
- 利用stm32两路pwm输出作为编码器接口两路输入信号,计数结果可用串口显示,pwm信号可用逻辑分析仪显示-Use-STM32 two PWM output as encoder interface two input signals, count results available serial port PWM signal can be used logic analyzer
STM32-usat
- stm32 f103 单片机 串口接受发字符数据(测试成功)!-STM32 F103 microcontroller serial port that accepts character data (tested successfully)!
USBTOUART6
- usb转串口,stm32 芯片,实现USB转串口功能-usb to serial port, stm32 chip USB to serial port functions
STM32-144-USB2serial_huanye
- 本例程通过虚拟的方法实现uSB口转化为串口的实用程序,不需采用电平转换的芯片即可实现-The routine method uSB through virtual serial port into a utility, without using the chip level conversion can be realized
STM32-camera
- 本实验将实现如下功能:开机后,初始化摄像头模块(OV7670),如果初始化成功,则在LCD模块上面显示摄像头模块所拍摄到的内容。我们可以通过KEY0设置光照模式(5种模式)、通过KEY1设置色饱和度,通过KEY2设置亮度,通过WK_UP设置对比度,通过TPAD设置特效(总共7种特效)。通过串口,我们可以查看当前的帧率(这里是指LCD显示的帧率,而不是指OV7670的输出帧率),同时可以借助USMART设置OV7670的寄存器,方便大家调试。DS0指示程序运行状态。-The experiment
STM32-control-CC1101
- STM32控制CC1101发送接收的源代码,可通过串口调试工具查看接收到的数据。-STM32 control CC1101 transmit and receive the source code, can be received through the serial port debugging tool to view the data.
STM32--SD-RW
- 开机先初始化SD卡,如果SD卡初始化完成,则读取扇区0的数据,然后通过串口打印-Boot initializes the SD card, if the SD card initialization is complete, the read sector 0 of the data, and then print through the serial port
STM32-clock
- 基于STM32实现电子时钟的设计,可以通过按键、或者串口来进行时间设置-STM32-based electronic clock design, can be key, or serial port to set the time
STM32-VirtualCOM
- STM32通过USB模拟串口,并将接收的数据,发回USB串口,同时显示在128×64点阵屏上。-STM32 serial port via USB emulation and data received back USB port, while in the 12864 dot matrix display screen.
STM32-UART-IAP
- 在STM32上通过串口实现IAP的源代码,可用于学习STM32上IAP的原理,或直接移植使用。-In STM32 IAP through the serial port on the source code can be used to learn the principles of the STM32 IAP or directly transplanted to use.
stm32-base-station
- STM32 基站程序,用于接收信号,并通过串口传给上位机,无线模块采用nRF24L01-STM32 base program for the received signal to the host computer via the serial port, using the nRF24L01 wireless module
STM32-USART-send-and-receive-data-
- 本程序目的是提供使用stm32串口收发一帧数据的一种方法,采用中断方式接受和发送,每进一次中断接收或发送一字节,可以实现pc机与板子通信或板子与板子间通信。注意本程序中外接高速晶振为12M赫兹,而大部分板子为8M赫兹,本程序所用芯片是stm32RBT6-The purpose of this procedure is to provide a method of using STM32 serial port to send and receive a data, using interrupt
STM32-led-blinjk-for-ucos
- STM32 开发板基于 uCosII 2.86 的 LED灯闪烁实验 开发板上电后,LED1-3 会按照默认的 500ms 间隔,明暗闪烁,此时可以通过 串口助手 SSCOM3.2 发出指令,设置 LED1,LED2,LED3 的闪烁间隔时间。间隔范围是 1-65535ms。可以设置任意一个 LED 得闪烁间隔时间, 通过这个实验,可以学习 ucosII 的 任务建立,及任务调度, 事件同步等内容。-STM32 development board based uCosII
STM32-GPIO_uart
- 利用GPIO、EXTI外部中断、TIM定时器实现URAT串口,该例子来自21IC网,未做改动,明天自己调试,看看效果 完全是根据UART协议编写-Using GPIO, EXTI external interrupt, TIM timer URAT serial port, the example from 21 IC net, do not make changes, their debugging tomorrow, see the effect Writing is e
STM32-8-channel-ADCPTFT
- 8通道ADC+TFT+串口发送,包括针对8通道ADC数据进行显示及发送处理的各种要求-8 channel ADC+TFT+ serial port to send, including a variety of display and transmit processing for 8 channel ADC data requirements
STM32-counter
- STM32 使用外部中断作为计数器 可以通过串口查看计数值 还有暂停计数功能-STM32 using an external interrupt can still be suspended as a counter counting functions via the serial port to view the count value
STM32-sensor-experiment
- stm32温度与湿度传感器实验,本实验采用野火M3控制温湿度传感器DHT11,通过串口打印到终端的信息,读取DHT11成功!湿度为35.0 %RH ,温度为 32.0℃-STM32 temperature and humidity sensor experiment, this experiment adopts the wildfire M3 control of temperature and humidity sensor DHT11, to the terminal informatio
STM32-USB-To-COM
- STM32F103系列USB虚拟串口使用,调试通过正常使用-STM32F103 series of USB virtual serial port to use, debugging through normal use
STM32-usart
- stm32串口通信 该程序中将串口1和串口的驱动进行了测试。-stm32 serial port codes testing
uart
- STM32通过串口和上位机的对话,STM32在收到上位机发过来的字符串后,原原本本的返回给上位机-STM32 through dialogue and PC' s serial port, STM32 PC after a string sent me the receipt, exactly back to the host computer