搜索资源列表
stm32GPIO测试程序
- 可以用来测试stm32开发板的GPIO
STM32_GPIO
- STM32微处理器的GPIO,有关其GPIO相关的寄存器的配置和应用-STM32 microcontroler GPIO,in this file ,it specify the register of the GPIO and show how to configure the register and how to using it
LED
- 基于STM32下,在IAR环境下,自己编写的中断控GPIO的LED灯的源码。-Based on the STM32, the environment in the IAR, write your own interrupt control the LED light source GPIO.
1_GPIO
- 跑马灯都是你们要接触的第一个程序.对于STM32来说,由于有官方库这种东西的出现,使得原来很麻烦的寄存器初始化变的相对简单.本例程主要让大家感受一下最基本的库操作GPIO 的方法.-Marquees are you want to contact a program for the STM32 is the official repository, the emergence of this kind of thing makes the original a lot of trouble re
实验1 跑马灯实验
- STM32gpio调试例程,希望对你有所帮助((an example of STM32F10x GPIOTEST))
定时器中断
- stm32芯片定时器的中断的实现,对32定时器的初始化和GPIO口的操控(STM32 chip timer interrupt the realization of the 32 timer initialization and GPIO port control)
stm学习中程序
- 其中包含了一个以gpio简单设置的程序以及usart通信和pwm设置的程序(It contains a program that is simple to set up with GPIO, as well as programs for USART communications and PWM settings)
【19】DMA PWM WS2812 GPIO输出16组
- STM32作为主控芯片,72Mhz,利用DMA+PWM实现驱动WS2812,创建16个并行800kBit / s数据流的想法如下: 使用定时器每1.25us创建一个800kHz的时基和一个DMA请求。 使用2个比较模块在低位时间(350ns)和高位时间(700ns)下创建DMA请求 1.25us DMA请求将GPIO端口的所有位设置为高电平 350ns DMA请求将数据从帧缓冲区传输到GPIO端口。如果该位为0,GPIO引脚将变为低电平,否则将保持高电平。 700ns DMA请求将所有
12-GPIO输出—使用固件库点亮LED灯
- STM32点亮LED灯2313122332(The HA is according to the time of the story of the world)
正点原子战舰STM32-LCD12864显示-GPIO全部F口
- 基于stm32单片机开发的LCD12864液晶显示程序(The LCD12864 LCD program based on STM32 microcontroller)
NewWind-V1.4
- 完成段码屏显示、风机转速pwm控制、 pm2.5测量、CO2测量。(Completion of section code screen display, fan speed, PWM control)
4、GPIO-流水
- 基于SYM32F103VET6的超级流水程序 指的一看 初学者必学(SYM32F103VET6 based super water program refers to a look, beginners must learn)
project
- stm32的GPIO配置,做小车程序的一个工程模板,不用自己建立工程了,KEIL5可用(STM32's GPIO configuration, as an engineering template for the car program, does not build the project itself, KEIL5 is available.)
ALIENTEK MINISTM32 实验1 跑马灯
- 使用stm32的GPIO模式, 完成LED的操作(Use the GPIO mode of STM32 to complete the operation of the LED)
1、LED
- 流水灯,对于GPIO口的配置和利用,使得led灯逐个点亮(Flow lamp For the configuration and use of the GPIO port, the LED lights are lit by one by one)
STM32F103C8T6 NRF24L01
- 经测试,此代码可以实现2.4G(NRF24L01)的通信。 内有大量的注释,初学者可以看注释弄明白 其中还有其他的代码,软件SPI通信方式、串口、GPIO口、延时。(After testing, this code can implement the communication of 2.4G (NRF24L01). There are a lot of annotations, and the beginners can see the annotations to understand
ALIENTEK MINISTM32 实验1 跑马灯
- 利用STM32的GPIO输出高低电平,实现跑马灯的效果(Using the GPIO output voltage of STM32, to achieve marquee effect)
STM32使用I2C驱动GY-30光照传感器和SPI总线驱动DHT11
- 对于光照传感器的使用,在串口调试助手上将光照强度显示出来,每隔2S,读取一次,否则会出现读取失败。 对于温湿度传感器也是同样的道理,只是为了节省GPIO口,使用SPI单总线通信模式,实现对于温湿度的数据采集以及显示。 其中还包括了对应的串口通信,以及对于printf的重定向,使其打印在串口助手的接收区。
USB-HID-20191231
- 用STM32做的一个USB 模拟发送按键到PC上 当GPIO按下的时候 模拟指定的字符发上来,模拟游戏按下的动作(Use a USB analog send button made by STM32 to send to PC when GPIO is pressed, simulate the action of game pressing)
STM32模拟SPI四种工作模式
- STM32有时会用到由GPIO端口模拟SPI的情况,此代码是模拟SPI四种工作模式