搜索资源列表
温升测试
- 电机温升测试系统,适用于工作频率为50/60Hz的单/三相小功率异步电机(≤5KW)、串级电机、电动工具的绕组温升测量。适用于工作频率为50/60Hz的电源变压器、充电器、电感镇流器的绕组温升测量。带电原理:在带电工作情况下测量绕组的直流电阻,并用公式折算成温升。专为电动工具定子,转子温升测量而开发,其中定子采用带电法,转子采用断电法-motor temperature test system is applicable to the frequency of 50/60Hz single /
prohl
- 计算关于转子动力学中,如何求传递矩阵的的系数的程序-calculated on rotor dynamics, how to request the transfer matrix of the coefficients of procedures
armok013182
- 三相步进电机的三相六拍工作方式,正转的绕组通电顺序:A、AB、B、BC、C、CA、A,反转的通电顺序:A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性,故步进电机的工作过程中不能及时的启动和停止,在启动时应慢慢的加速到预定速度,在停止前应逐渐减速到停止,否则,将产生失步现象。 步进电机的控制问题可总结为两点: 1、产生工作方式需要的时序脉冲; 2、控制步进电机的速度,使它始终遵循加速、匀速、减速的规律工作。
zhonghemoxing
- 用matlab编制的转子裂纹综合模型供做此方面设计的人参考。
mt
- 电机矢量控制,将电机转子,定子定位在MT轴,simulink仿真-motor simulink
Study-on-Starting-up-Method-of-PMSM-Based-on-Hybri
- 基于复合式光电编码器永磁同步电机启动方法的研究 简述了复合式光电编码器的工作原理,分析现有永磁同步电机转子位置检测方法的不足,提出了使用复合式光电编码器对永磁同步电机转子初始位置检测及电机启动的方法,最后通过以数字信号处理器(DSP)为核心的实验平台进行实验,实验结果表明,该方法可以满足实际使用的要求,实现了电机可靠启动、运行。-The operating principle of hybrid grating encoder was introduced and the shortcomi
ALA
- ALA转子电机的simlink建模及仿真 -ALA rotor motor simlink Modeling and Simulation
dd
- 介绍了无刷双馈异步风力发电机的结构及其发电调速原理。从无刷双馈电机的基 本方程出发,通过坐标变换,建立了无刷双馈电机在转子旋转坐标系下的d-q 模型,并进行了Matlab 建模和仿真。-Introduced a brushless doubly-fed induction wind turbine structure and the principle of generating speed. BDFM from the basic equations, coordinate transfo
foc
- 异步电机转子磁场定向控制仿真模型,通过验证,好用!-FOC induction motor simulation models, easy to use!
Senior_Design_vc_rotor_test_ad
- vc高级设计广告转子测试代码Senior Design vc rotor test ad code -Senior Design vc rotor test ad code
liulianji
- 用于转子流量计的选型计算,不依赖任何数据库,选型结果可生成文本文档,短小精悍-Used for the Rotameter the selection calculation, not relying on any database, the selection results can generate a text document, dapper
rotor-bearing-(2-3-4-5-6)
- 转子-轴承系统动态设计技术(第2,3,4,5,6部分)-rotor-bearing dynamics technology design guide(2,3,4,5,6)
shaungzhuanzi
- 此程序是双转子系统临界转速计算源程序代码(This program is the double rotor system critical speed calculation source code)
B_waizhuanzi_2D
- 计算永磁无刷直流电机的气隙磁场---外转子坐标系下的(Calculation of the air gap magnetic field of permanent magnet brushless DC motor in the outer rotor coordinate system)
碰摩力程序
- 转子碰摩力模型程序,不平衡量在m2处,碰摩也发生在m2处。积分步长不够小,改小就ok(The rotor rub impact model program)
转子断条故障模拟(Ansoft)
- 采用MAXWELL/ANSYS的异步电动机转子断条故障的模拟,可直接运行(The rotor broken bar fault of asynchronous motor with MAXWELL/ANSYS can be simulated directly, and it can run directly)
virbration
- 复合材料转子动力学仿真模型,可输出振动特性曲线(Rotor dynamic simulation model of composite material, which can output vibration characteristic curve)
Rotor thrust calculator
- 该算法适用于各种转子采用无刷直流电机和ESC(显然)。 特别是本程序只适用与串口通信准备Arduino电路板。 你可以如果你没有Arduino开发板改变最初的声明。 从实际电机/转子u计算,必须有一个微控制器,将获得MATLAB命令,并将命令发送到特定的引脚上的ESC电机连接。请注意,引脚必须是一个PWM能力。(The algorithm is suitable for the use of Brushless DC motor and ESC (obviously) for variou
rotor_criticalspeed_calculation
- 利用传递矩阵法,实现航空发动机转子的临界转速计算(The critical speed calculation of aeroengine rotor is realized by transfer matrix method.)
CV_CT_IMM
- 分析转子不平衡响应,以及转子涡动,转子坎贝尔图临界转速求解等((Cambridge Aerospace Series) Michael I. Friswell, John E. T. Penny, Seamus D. G)